manualshive.com logo in svg

IBM System x3650 M5, Installation And Service Manual, Page: 861 / 1010

Share
Download
IBM System x3650 M5 Installation And Service Manual Download Page 861

405-905-000

BRCM:TestLoopbackMAC Test Failed

Explanation:

BRCM:TestLoopbackMAC Test Failed.

Severity:

Error

Serviceable:

Yes

Recoverable:

No

Automatically notify Support:

No

User response:

Complete the following steps:

1.

Check component firmware level and upgrade if necessary. The installed firmware level can be found in the DSA
Diagnostic Event Log within the Firmware/VPD section for this component.

2.

Rerun the test.

3.

If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service Guide" for the
next corrective action.

Related Links:

v

IBM Support Website

v

Latest level of DSA

v

Latest level of BMC/IMM

405-906-000

BRCM:TestLoopbackPhysical Test Failed

Explanation:

A failure was detected during the loopback test at the physical layer.

Severity:

Error

Serviceable:

Yes

Recoverable:

No

Automatically notify Support:

No

User response:

Complete the following steps:

1.

Check component firmware level and upgrade if necessary. The installed firmware level can be found in the DSA
Diagnostic Event Log within the Firmware/VPD section for this component.

2.

Rerun the test.

3.

If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service Guide" for the
next corrective action.

Related Links:

v

IBM Support Website

v

Latest level of DSA

v

Latest level of BMC/IMM

405-905-000 • 405-906-000

Appendix C. DSA diagnostic test results

845

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments