IBM System x3650 M5 Installation And Service Manual Download Page 265

Page: 265 / 1010

Connect the cable to the rear of the LCD system information display panel.

Slide the LCD panel assembly into the server until it clicks into place.

10.

Connect the LCD panel assembly cable to the system board.
The following illustration shows the cable routing for the LCD panel
assembly.

Retention bracket

Figure 200. Retention bracket installation

LCD panel assembly

Figure 201. LCD panel assembly installation

Chapter 5. Removing and replacing components

249

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M5

Reviews:

IBM System x3650 M5, Installation And Service Manual, Page: 265 / 1010

Search results

Summary of Contents for System x3650 M5

Reviews: