IBM System x3650 M5 Installation And Service Manual Download Page 328

Page: 328 / 1010

Table 16. Events that automatically notify Support (continued)

Event ID

Message String

Automatically
Notify
Support

806f0207-2584ffff

[ProcessorElementName] has Failed with
FRB1/BIST condition. (All CPUs)

Yes

806f020d-0400ffff

Failure Predicted on drive
[StorageVolumeElementName] for array
[ComputerSystemElementName]. (Drive 0)

Yes

806f020d-0401ffff

Failure Predicted on drive
[StorageVolumeElementName] for array
[ComputerSystemElementName]. (Drive 1)

Yes

806f020d-0402ffff

Failure Predicted on drive
[StorageVolumeElementName] for array
[ComputerSystemElementName]. (Drive 2)

Yes

806f020d-0403ffff

Failure Predicted on drive
[StorageVolumeElementName] for array
[ComputerSystemElementName]. (Drive 3)

Yes

806f020d-0404ffff

Failure Predicted on drive
[StorageVolumeElementName] for array
[ComputerSystemElementName]. (Drive 4)

Yes

806f020d-0405ffff

Failure Predicted on drive
[StorageVolumeElementName] for array
[ComputerSystemElementName]. (Drive 5)

Yes

806f020d-0406ffff

Failure Predicted on drive
[StorageVolumeElementName] for array
[ComputerSystemElementName]. (Drive 6)

Yes

806f020d-0407ffff

Failure Predicted on drive
[StorageVolumeElementName] for array
[ComputerSystemElementName]. (Drive 7)

Yes

806f020d-0408ffff

Failure Predicted on drive
[StorageVolumeElementName] for array
[ComputerSystemElementName]. (Drive 8)

Yes

806f020d-0409ffff

Failure Predicted on drive
[StorageVolumeElementName] for array
[ComputerSystemElementName]. (Drive 9)

Yes

806f020d-040affff

Failure Predicted on drive
[StorageVolumeElementName] for array
[ComputerSystemElementName]. (Drive 10)

Yes

806f020d-040bffff

Failure Predicted on drive
[StorageVolumeElementName] for array
[ComputerSystemElementName]. (Drive 11)

Yes

806f020d-040cffff

Failure Predicted on drive
[StorageVolumeElementName] for array
[ComputerSystemElementName]. (Drive 12)

Yes

806f020d-040dffff

Failure Predicted on drive
[StorageVolumeElementName] for array
[ComputerSystemElementName]. (Drive 13)

Yes

806f020d-040effff

Failure Predicted on drive
[StorageVolumeElementName] for array
[ComputerSystemElementName]. (Drive 14)

Yes

312

System x3650 M5 Type 5462: Installation and Service Guide

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M5

Reviews:

IBM System x3650 M5, Installation And Service Manual, Page: 328 / 1010

Search results

Summary of Contents for System x3650 M5

Reviews: