IBM System x3650 M5 Installation And Service Manual Download Page 182

Page: 182 / 1010

10.

Connect the optical drive cable (see “Replacing the optical drive cable” on
page 161).

11.

Reconnect the power cords and any cables that you removed.

12.

Turn on the peripheral devices and the server.

Removing a memory module

Use this information to remove a memory module.

About this task

To remove a dual inline memory module (DIMM), complete the following steps:

Procedure

Read the safety information that begins on “Safety” on page vii and
“Installation guidelines” on page 283.

Turn off the server and peripheral devices and disconnect all power cords.

Remove the top cover (see “Removing the top cover” on page 146).

Remove the air baffle (see “Removing the air baffle” on page 148).

Carefully open the retaining clips on each end of the DIMM connector and
remove the DIMM.

Attention:

To avoid breaking the retaining clips or damaging the DIMM

connectors, open and close the clips gently.

Drive retainer clip

Figure 92. Optical drive installation

166

System x3650 M5 Type 5462: Installation and Service Guide

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for System x3650 M5

Reviews:

IBM System x3650 M5, Installation And Service Manual, Page: 182 / 1010

Search results

Summary of Contents for System x3650 M5

Reviews: