manualshive.com logo in svg

IBM System x3650 M5, Installation And Service Manual, Page: 489 / 1010

Share
Download
IBM System x3650 M5 Installation And Service Manual Download Page 489

806f011b-2502ffff

The connector [PhysicalConnectorElementName] has encountered a configuration error.

(nvDIMM 02 Cable)

Explanation:

This message is for the use case when an implementation has detected an Interconnect Configuration

Error.

May also be shown as 806f011b2502ffff or 0x806f011b2502ffff

Severity:

Error

Alert Category:

Critical - Other

Serviceable:

Yes

CIM Information: Prefix:

PLAT and

ID:

0266

SNMP Trap ID:

50

Automatically notify Support:

Yes

User response:

If the specified sensor is front USB connector, reset the front USB cable on the system board. If the

specified sensor is front video connector, reset the front video cable in the system board. If the specified sensor is
PwrPaddle cable, complete the following steps until problem is solved:

1.

Reseat the power paddle cable on the system board.

2.

Replace the power paddle cable.

3.

(Trained technician only) Replace the supercap n. (n = supercap number)

4.

(Trained technician only) Replace the system board.

806f011b-2505ffff

The connector [PhysicalConnectorElementName] has encountered a configuration error.

(nvDIMM 05 Cable)

Explanation:

This message is for the use case when an implementation has detected an Interconnect Configuration

Error.

May also be shown as 806f011b2505ffff or 0x806f011b2505ffff

Severity:

Error

Alert Category:

Critical - Other

Serviceable:

Yes

CIM Information: Prefix:

PLAT and

ID:

0266

SNMP Trap ID:

50

Automatically notify Support:

Yes

User response:

If the specified sensor is front USB connector, reset the front USB cable on the system board. If the

specified sensor is front video connector, reset the front video cable in the system board. If the specified sensor is
PwrPaddle cable, complete the following steps until problem is solved:

1.

Reseat the power paddle cable on the system board.

2.

Replace the power paddle cable.

3.

(Trained technician only) Replace the supercap n. (n = supercap number)

4.

(Trained technician only) Replace the system board.

806f011b-2502ffff • 806f011b-2505ffff

Appendix A. Integrated management module II (IMM2) error messages

473

Summary of Contents for System x3650 M5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments