manualshive.com logo in svg

IBM RS/6000 SP, Maintenance Information

The IBM RS/6000 SP handbook offers detailed instructions on how to maximize the performance of your system. Download the manual for free from manualshive.com to learn about the innovative features and functionalities of this powerful product. Get all the information you need to optimize your IBM RS/6000 SP experience.

Share
Download
background image

 

MAP 0520: Switch Assembly Environment

 

 

044 (continued)
Is this a PS1Fail problem?
Yes  No

045

– Replace power supply card PS2. Refer to "Removing the Switch Power Card(s) (HiPS 3.0,

HiPS-LC8, SPS, SPS-8)" in

 IBM RS/6000 SP: Maintenance Information, Volume 3, Locations and

Service Procedures.

– Reinstall the SPS front panel assembly, being careful to align the guide pins on the P1 to the

inner chassis cup guide.

– Replug the power cable (J1) and supervisor cable (J2) to the rear of the assembly.
– Put the circuit breaker in the on (‘1’) position.
Does the PS2Fail condition still exist?
Yes  No

046

– Go to Step 030 on page 1-307.

047

– Go to Step 050.

048

– Replace power supply card PS1. Refer to "Removing the Switch Power Card(s) (HiPS 3.0, HiPS-LC8,

SPS, SPS-8)" in

 IBM RS/6000 SP: Maintenance Information, Volume 3, Locations and Service Proce-

dures.

– Reinstall the SPS front panel assembly, being careful to align the guide pins on the P1 to the inner

chassis cup guide.

– Replug the power cable (J1) and supervisor cable (J2) to the rear of the assembly.
– Put the circuit breaker in the on (‘1’) position.
Does the PS1Fail condition still exist?
Yes  No

049

– Go to Step 030 on page 1-307.

050

– Put the circuit breaker in the Off (‘0’) position?
– Remove the power cable (J1) and supervisor cable (J2) from the rear of the switch assembly. Then

remove the front panel assembly.

– Replace the supervisor card. Refer to "Removing the Switch Supervisor Card (HiPS 3.0, HiPS-LC8,

SPS, SPS-8)" in

 IBM RS/6000 SP: Maintenance Information, Volume 3, Locations and Service Proce-

dures.

– Reinstall the SPS front panel assembly, being careful to align the guide pins on the P1 to the inner

chassis cup guide.

– Replug the power cable (J1) and supervisor cable (J2) to the rear of the assembly.
– Put the circuit breaker in the On (‘1’) position?
(Step 050 continues)

1-310

RS/6000 SP MAPs 

 

Summary of Contents for RS/6000 SP





































































































































































































































































































































































































Reviews:

No comments

Related manuals for RS/6000 SP

F5 VIPRION 2400 Platform Manual preview
VIPRION 2400
Brand: F5 Pages: 72
LaCie 2big Network 2 Datasheet preview
2big Network 2
Brand: LaCie Pages: 4
i3 International SRX-Pro Server Quick Start Manual preview
SRX-Pro Server
Brand: i3 International Pages: 2
IBM AMD Opteron LS20 Type 8850 Installation And User Manual preview
AMD Opteron LS20 Type 8850
Brand: IBM Pages: 68
Galleon NTS-6001 Configuration Manual preview
NTS-6001
Brand: Galleon Pages: 47
Gigabyte W131-X30 Quick Installation Manual preview
W131-X30
Brand: Gigabyte Pages: 2
Supermicro SuperServer 1029P-MT User Manual preview
SuperServer 1029P-MT
Brand: Supermicro Pages: 123
Rasilient ApplianceStor 75 User Manual preview
ApplianceStor 75
Brand: Rasilient Pages: 24
HP ProLiant BL460c Gen8 User Manual preview
ProLiant BL460c Gen8
Brand: HP Pages: 84
Air Live WFP-101U v2 Quick Start Manual preview
WFP-101U v2
Brand: Air Live Pages: 87
Gigafast EE171-PR User Manual preview
EE171-PR
Brand: Gigafast Pages: 74
SAP XI 3.1 Manual preview
XI 3.1
Brand: SAP Pages: 32
Inventec N800G3 User Manual preview
N800G3
Brand: Inventec Pages: 258
Uniwide AR3016G Hardware User'S Manual preview
AR3016G
Brand: Uniwide Pages: 96
Lantronix XPress-DR Plus Quick Start Manual preview
XPress-DR Plus
Brand: Lantronix Pages: 8
SMC Networks FieldServer FS-8700-60 Gardner Denver Driver Manual preview
FieldServer FS-8700-60 Gardner Denver
Brand: SMC Networks Pages: 13
Thales SafeNet ProtectServer Network HSM 5.9 Installation And Configuration Manual preview
SafeNet ProtectServer Network HSM 5.9
Brand: Thales Pages: 37
H3C UniServer B5800 G3 User Manual preview
UniServer B5800 G3
Brand: H3C Pages: 78

Brands by name

Popular brands

Load more brands