IBM RS/6000 SP Page 216 Maintenance Information Download | Manualshive

Page: 216 / 388

background image

MAP 0330: POWER3 SMP Thin and Wide Node Environment

045

– Remove processor node from service position.
– From the control workstation, power on the processor node.
Is the power supplies green LED off or flashing?
Yes No

046

Go to Step 055 on page 1-197.

047

Go to Step 044 on page 1-195 and replace the next highest priority component.

048

Problem with 48 volts supplied to power supply.
– Place the POWER3 SMP node into service position. Replace the node supervisor card. Refer to

"Replacing the Node Supervisor Card" in

IBM RS/6000 SP: Maintenance Information, Volume 3,

Locations and Service Procedures.

– Replace the POWER3 SMP node from the service position.
Is the power supplies green LED Off or flashing?
Yes No

049

– Go to Step 055 on page 1-197.

050

– Place the POWER3 SMP node in service position, and replace the power/supervisor cable assembly.

Refer to "Replacing the Power/Supervisor Cable Assembly" in

IBM RS/6000 SP: Maintenance Informa-

tion, Volume 3, Locations and Service Procedures.

– Replace the POWER3 SMP node from the service position.
(Step 050 continues)

Priority

Component

Action

1

Service processor card

1. Replace card

2. Go to Step 045 on page 1-196

2

I/O expansion control cable

1. Replace cable assembly

2. Go to Step 045 on page 1-196

3

CPU or I/O power assembly

1. Replace assembly

2. Go to Step 045 on page 1-196

4

I/O planar

1. Replace planar

2. Go to Step 045 on page 1-196

5

Power or power/supervisor cable
assembly

1. Replace assembly

2. Go to Step 045 on page 1-196

6

All replaced

Call next level of support.

1-196

RS/6000 SP MAPs

«
...
214
215
216
217
218
...
»

Summary of Contents for RS/6000 SP





































































































































































































































































































































































































Reviews:

No comments

Related manuals for RS/6000 SP

Brand: Acano Pages: 17

5big - Network NAS Server

Brand: LaCie Pages: 9

Brand: LaCie Pages: 14

MCX-2000 - MusicCAST Digital Audio Server

Brand: Yamaha Pages: 25

Brand: IBM Pages: 214

digitalSTROM-Server

Brand: aizo Pages: 2

Brand: Patton electronics Pages: 121

Brand: ONELAN Pages: 24

Brand: TYAN Pages: 170

Brand: i3 International Pages: 2

Modbus Server-Cerberus ISO1745

Brand: IntesisBox Pages: 5

H SERIES RS/6000

Brand: IBM Pages: 424

Brand: TYANO Pages: 102

Brand: Olive Pages: 103

Brand: Stratus Pages: 106

PRIMERGY PG-RSBOP2

Brand: Fujitsu Pages: 68

SPARC Enterprise T5440 Server

Brand: Fujitsu Pages: 92

SPARC Enterprise T5140

Brand: Fujitsu Pages: 138

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands