IBM RS/6000 SP Maintenance Information Download | Manualshive

Page: 350 / 388

background image

MAP 0540: Switch Function

L03-N01

identifies Logical frame 3, Node 1

E02-N04

identifies Physical frame 2, Node 4

S01-S02-BH-J3

identifies Multi-switch frame 1, slot 2, BH-J3

Refer to notes at beginning of “MAP 0540: Switch Function” on page 1-322 for more information on
cable connections and logical-to-physical frame translations.

3. Be aware that for logical frames consisting of two physical frames, all out.top even-numbered

nodes represent nodes physically located in the expansion frame (F/C 1010) but at the next lower
slot number. For example, L01-N04 (logical frame 1, node 4) could be physically located at E02-N03
(physical frame 2, slot 3).

Priority

Message/Condition

Action

1

“On board connections...”

Go to Step 093 on page 1-349 to replace the switch
assembly.

2

“Primary node connection...”

“Node connections...” on same
switch as primary node

If this is a standard node, go to Step 009 to
check “primary” or “secondary” processor node
connection.

If this is a dependent node (connection to router),
go to “MAP 0550: Dependent Node” on
page 1-351.

3

“Wrapped ports”

“frame # to frame #”

“switch # to switch #”

“Switch connections...”

Go to Step 042 on page 1-340 to check the wrapped
port or external switch connection.

4

“Node connections...” not on same
switch as primary node.

If this is a standard node, go to Step 009 to
check “secondary” processor node connection.

If this is a dependent node (connection to router),
go to “MAP 0550: Dependent Node” on
page 1-351.

5

All problems in
/var/adm/SPlogs/css/out.top file
have been addressed.

Go to Step 101 on page 1-350.

009

The /var/adm/SPlogs/css/out.top file indicates a problem with a “Primary node” or “Secondary node”
connection.
– Open frame rear cover and check the cable connection from the indicated switch assembly jack to the

processor node.

Is there a cable connected to the indicated jack on the switch assembly?
Yes No

010

No cable connected at the indicated jack. Refer to the table in "HiPS 2.0/3.0 Node Data Cables" in
IBM RS/6000 SP: Maintenance Information, Volume 3, Locations and Service Procedures, as
required.
(Step 010 continues)

1-330

RS/6000 SP MAPs

«
...
348
349
350
351
352
...
»

Summary of Contents for RS/6000 SP





































































































































































































































































































































































































Reviews:

No comments

Related manuals for RS/6000 SP

Brand: Buffalo Pages: 2

SuperServer 1026T-M3

Brand: Supero Pages: 104

8676 - Eserver xSeries 335

Brand: IBM Pages: 172

A+ AS-2124US-TNRP

Brand: Supermicro Pages: 130

Brand: Abit Pages: 56

FusionServer G8600 V7

Brand: xFusion Digital Technologies Pages: 112

SuperServer 6024H-82

Brand: Supero Pages: 122

Brand: IBM Pages: 75

FusionServer 2298 V5

Brand: Fusion Pages: 89

2500 - Color LaserJet Laser Printer

Brand: HP Pages: 24

Brand: HP Pages: 26

4650 - Color LaserJet Laser Printer

Brand: HP Pages: 2

615N - JetDirect Print Server

Brand: HP Pages: 56

4550 - Color LaserJet Laser Printer

Brand: HP Pages: 32

600N - JetDirect Print Server

Brand: HP Pages: 44

170X - JetDirect Print Server

Brand: HP Pages: 30

170X - JetDirect Print Server

Brand: HP Pages: 80

Brand: HP Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands