manualshive.com logo in svg

IBM RS/6000 SP, Maintenance Information

The IBM RS/6000 SP handbook offers detailed instructions on how to maximize the performance of your system. Download the manual for free from manualshive.com to learn about the innovative features and functionalities of this powerful product. Get all the information you need to optimize your IBM RS/6000 SP experience.

Share
Download
background image

 

 

MAP 0480: Open in 48 Volt DC Distribution

 

009 (continued)
– Check the 3-digit LEDs for the processor nodes to make sure they are all IPLing okay.
Do all processor nodes IPL okay?
Yes  No

010

Processor nodes not IPLed.
– Go to “MAP 0100: Start of Service Call” on page 1-4 to continue service.

011

Processor nodes have IPLed okay.
Does this frame contain a switch assembly?
Yes  No

012

Problem resolved.
– Go to “MAP 0570: End of Call” on page 1-357.

013

– Go to Step 014.

014

Frame contains switch assemblies.
– Go to Step 101 on page 1-350 of the “MAP 0540: Switch Function” on page 1-322 to verify fix.

   

Chapter 1. Maintenance Analysis Procedures (MAPs)

1-285

Summary of Contents for RS/6000 SP





































































































































































































































































































































































































Reviews:

No comments

Related manuals for RS/6000 SP

Lantronix SLC 8000 Demo Manual preview
SLC 8000
Brand: Lantronix Pages: 10
Lantronix xport pro Integration Manual preview
xport pro
Brand: Lantronix Pages: 17
Lantronix PremierWave XC User Manual preview
PremierWave XC
Brand: Lantronix Pages: 109
Lantronix XPort Integration Manual preview
XPort
Brand: Lantronix Pages: 24
Lantronix WiPort Integration Manual preview
WiPort
Brand: Lantronix Pages: 29
Lantronix XPress DR+ Quick Connect preview
XPress DR+
Brand: Lantronix Pages: 2
IBM System x3100 M4 Problem Determination And Service Manual preview
System x3100 M4
Brand: IBM Pages: 332
Sun Fire X4600 Installation Manual preview
X4600
Brand: Sun Fire Pages: 66
7starlake ROC286B User Manual preview
ROC286B
Brand: 7starlake Pages: 32
Kontron CG2100 Installation And Maintenance Manual preview
CG2100
Brand: Kontron Pages: 110
Ovislink AirLive WP-203G User Manual preview
AirLive WP-203G
Brand: Ovislink Pages: 132
TYAN Transport TX46 (B4985) Service Service Manual preview
Transport TX46 (B4985) Service
Brand: TYAN Pages: 75
AXIOMTEK NA-0043A Hardware Installation Manual preview
NA-0043A
Brand: AXIOMTEK Pages: 58
PalatiumCare Palcare PAL-211401 Install Manual preview
Palcare PAL-211401
Brand: PalatiumCare Pages: 64
Kontron Embedded Computers PxV206 User Manual preview
PxV206
Brand: Kontron Embedded Computers Pages: 46
Samsung HT-F5550W User Manual preview
HT-F5550W
Brand: Samsung Pages: 58
SEH PS107 Quick Installation Manual preview
PS107
Brand: SEH Pages: 32
Thales SafeNet ProtectServer PCIe HSM 5.4 Installation Manual preview
SafeNet ProtectServer PCIe HSM 5.4
Brand: Thales Pages: 27

Brands by name

Popular brands

Load more brands