IBM RS/6000 SP Page 68 Maintenance Information Download

Page: 68 / 388

MAP 0130: Processor Node

Priority

Message or condition

Action

Power problem

Uniprocessor (Thin/Wide Node)

– Green LED off or flashing

SMP (Thin/Wide/High Node)

– LED #1 (green) off or flashing

(Power) Green LED off or flashing

Node has no power

All voltages at zero

Perform "Node/Switch Supervisor Self-Test" in

IBM

RS/6000 SP: Maintenance Information, Volume 3,
Locations and Service Procedures to verify operation
of LEDs.

If supervisor test fails, go to “MAP 0120: Super-
visor Bus Problem” on page 1-19.

If test passes, go to the applicable MAP:

– “MAP 0160: Thin Processor Node Power” on

page 1-69

– “MAP 0220: Wide Processor Node Power” on

page 1-105

– “MAP 0260: 604 or 604e High Node Power”

on page 1-130

– “MAP 0300: 332 MHz SMP Node Power” on

page 1-169

– SP-attached servers (RS/6000 Machine

Type 7017-S70 and S7A): Consult the
RS/6000 Enterprise Servers S70 and S7A
Installation and Service Guide.

Note: Before disconnecting cables or per-

forming service actions on an
SP-attached server, perform "Decou-
pling and Coupling Code for
SP-Attached Servers" in

RS/6000 SP:

Maintenance Information, Volume 3.

– “MAP 0340: POWER3 SMP Thin and Wide

Node Power” on page 1-200

to perform the required service action.

Power problem — SP-attached
servers (RS/6000 Machine Type
7017-S70 and S7A)

Check the server to SP connection cables for
correct plugging. Refer to "Installing SP-Attached
Server Cables " in

RS/6000 SP: Maintenance

Information, Volume 1. Consult the RS/6000
Enterprise Servers S70 and S7A Installation and
Service Guide to perform any required service
action.

Note: Before disconnecting cables or performing

service actions on an SP-attached server,
perform "Decoupling and Coupling Code
for SP-Attached Servers" in

RS/6000 SP:

Maintenance Information, Volume 3.

Go to “MAP 0190: Processor Node Function” on
page 1-87.

Processor problem

Front panel 3-digit LEDs non-
blank (OK=blank)

Go to “MAP 0190: Processor Node Function” on
page 1-87.

1-48

RS/6000 SP MAPs

Summary of Contents for RS/6000 SP





































































































































































































































































































































































































Search results

Summary of Contents for RS/6000 SP

Reviews:

Related manuals for RS/6000 SP

Brands by name

Popular brands

IBM RS/6000 SP, Maintenance Information

Search results

Summary of Contents for RS/6000 SP

Reviews:

Related manuals for RS/6000 SP

Brands by name

Popular brands