manualshive.com logo in svg

IBM RS/6000 SP, Maintenance Information

The IBM RS/6000 SP handbook offers detailed instructions on how to maximize the performance of your system. Download the manual for free from manualshive.com to learn about the innovative features and functionalities of this powerful product. Get all the information you need to optimize your IBM RS/6000 SP experience.

Share
Download
background image

 

MAP 0300: 332 MHz SMP Node Power

 

 

030 (continued)
Is the CB switched On?
Yes  No

031

Set the CB to the On position.
Did the CB switch on and stay on?
Yes  No

032

Did the CB trip?
Yes  No

033

– Go to Step 021 on page 1-171.

034

Possible power supply problem or short condition.
– Go to Step 043 on page 1-173.

035

– Go to Step 008 on page 1-169.

036

Node 48 volts missing.
– Go to MAP 0290: 332 MHz SMP Node Environment, Step 017 on page 1-161.

037

Check the node supervisor card yellow LED 5.
Is the yellow LED 5 Off?
Yes  No

038

Base code loaded on node supervisor card.
–  Go to "Updating the Node Supervisor Code" in 

IBM RS/6000 SP: Maintenance Information,

Volume 3, Locations and Service Procedures.

– Go to Step 050 on page 1-174.

039

– Check the power supplies green LED.
Is the power supplies green LED Off?
Yes  No

040

– Go to MAP 0290: 332 MHz SMP Node Environment, Step 014 on page 1-161.

1-172

RS/6000 SP MAPs 

 

Summary of Contents for RS/6000 SP





































































































































































































































































































































































































Reviews:

No comments

Related manuals for RS/6000 SP

IBM Enterprise Server S80 User Manual preview
Enterprise Server S80
Brand: IBM Pages: 282
Samsung ML-2010 - B/W Laser Printer Manual preview
ML-2010 - B/W Laser Printer
Brand: Samsung Pages: 25
LaCie 8BIG RACK THUNDERBOLT 2 Quick Start Manual preview
8BIG RACK THUNDERBOLT 2
Brand: LaCie Pages: 28
SEH SEH650 Network Installation Manual preview
SEH650
Brand: SEH Pages: 5
Patton electronics PeNet 2127 User Manual preview
PeNet 2127
Brand: Patton electronics Pages: 16
H3C UniServer R2900 G3 Installation, Quick Start preview
UniServer R2900 G3
Brand: H3C Pages: 15
Supermicro SSG-2029P-ACR24H User Manual preview
SSG-2029P-ACR24H
Brand: Supermicro Pages: 136
Compaq 244857-001 - TaskSmart - C4000 Model 60_duplicate Specification preview
244857-001 - TaskSmart - C4000 Model 60_duplicate
Brand: Compaq Pages: 9
SafeNet ProtectServer External 2 Installation Manual preview
ProtectServer External 2
Brand: SafeNet Pages: 22
Supero SuperServer 6024H-82 User Manual preview
SuperServer 6024H-82
Brand: Supero Pages: 122
BITMAIN AntMiner S9 Repair Manual preview
AntMiner S9
Brand: BITMAIN Pages: 20
TRENDnet TEW-P1P Quick Installation Manual preview
TEW-P1P
Brand: TRENDnet Pages: 9
Red Hat NETWORK PROXY 5.3.0 - Installation Manual preview
NETWORK PROXY 5.3.0 -
Brand: Red Hat Pages: 48
SSS Siedle Access Server M Upgrade Instructions preview
Access Server M
Brand: SSS Siedle Pages: 28
Inspur NE5260M5 User Manual preview
NE5260M5
Brand: Inspur Pages: 135
Digitus DN-7025 Quick Installation Manual preview
DN-7025
Brand: Digitus Pages: 8
I-O Corporation Pro Edge User Manual preview
Pro Edge
Brand: I-O Corporation Pages: 37
exemys SSE232-IA User Manual preview
SSE232-IA
Brand: exemys Pages: 39

Brands by name

Popular brands

Load more brands