IBM RS/6000 SP Page 332 Maintenance Information Download | Manualshive

Page: 332 / 388

background image

MAP 0520: Switch Assembly Environment

055 (continued)
Does the failure condition still exist?
Yes No

056

– Put the circuit breaker in the Off (‘0’) position.
– Remove power cable (J1) and supervisor cable (J2) from the rear of the switch assembly. Then

remove the front panel assembly.

– Replace power supply PS2. Refer to "Removing the Switch Power Card(s) (HiPS 3.0, HiPS-LC8,

SPS, SPS-8)" in

IBM RS/6000 SP: Maintenance Information, Volume 3, Locations and Service

Procedures.

– Replace switch from the service position. Refer to "Service Position Procedures" in

IBM RS/6000

SP: Maintenance Information, Volume 3, Locations and Service Procedures.

– Go to Step 030 on page 1-307.

057

– Put the circuit breaker in the Off (‘0’) position.
– Remove power cable (J1) and supervisor cable (J2) from the rear of the switch assembly. Then remove

the front panel assembly.

– Replug power supply PS2 and replace the switch supervisor card. Refer to "Removing the Switch

Supervisor Card (HiPS 3.0, HiPS-LC8, SPS, SPS-8)" in

IBM RS/6000 SP: Maintenance Information,

Volume 3, Locations and Service Procedures.

– Reinstall the SPS front panel assembly, being careful to align the guide pins on the P1 connector to the

inner chassis.

– Replug the power cable (J1) and supervisor cable (J2) at the rear of the assembly.
– Put the circuit breaker in the On (‘1’) position.
Does the failure condition still exist?
Yes No

058

– Go to Step 030 on page 1-307.

059

–

HiPS 2.0, HiPS 3.0, or HiPS-LC8 Replace switch assembly (see "Procedures for Switch Assemblies" in

IBM RS/6000 SP: Maintenance Information, Volume 3, Locations and Service Procedures).

SPS or SPS-8 Replace inner chassis assembly (see "Procedures for Switch Assemblies" in

IBM

RS/6000 SP: Maintenance Information, Volume 3, Locations and Service Procedures).

– Go to Step 030 on page 1-307.

1-312

RS/6000 SP MAPs

«
...
330
331
332
333
334
...
»

Summary of Contents for RS/6000 SP





































































































































































































































































































































































































Reviews:

No comments

Related manuals for RS/6000 SP

BladeCenter HS23

Brand: IBM Pages: 30

System x3950 X6

Brand: IBM Pages: 53

Brand: Panasonic Pages: 28

Brand: Vicon Pages: 2

totalstorage 200

Brand: IBM Pages: 152

digitalSTROM-Server

Brand: aizo Pages: 2

NetScaler MPX 25100 40G

Brand: Citrix Pages: 15

8668 - Eserver xSeries 232

Brand: IBM Pages: 182

SUPERSERVER 1018D-73MTF

Brand: Supero Pages: 124

Brand: King Pigeon Pages: 19

Brand: Digi Pages: 126

StorageWorks E Series

Brand: HP Pages: 8

StorageWorks 9000s NAS

Brand: HP Pages: 7

StorageWorks NAS e7000 v2

Brand: HP Pages: 2

StorageWorks NAS e7000 v2

Brand: HP Pages: 70

StorageWorks 600 All-in-One

Brand: HP Pages: 58

StorageWorks All-in-One SB600c - Storage Blade

Brand: HP Pages: 60

Brand: QNAP Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands