IBM RS/6000 SP Maintenance Information Download Page 17 | Manualshive

Page: 17 / 388

IBM RS/6000 SP Maintenance Information Download Page 17

About This Book

This book is to help you, as a customer engineer:

Isolate RS/6000 SP failures (as well as 9076 SP1 failures in an SP1/SP2 environment

Perform isolation and verification tests and identify field replaceable unit (FRU) locations

This book is to be used with:

IBM RS/6000 SP: Maintenance Information, Volume 1, Installation and Relocation (GA22-7375),
(referred to, throughout this publication, as

RS/6000 SP: Maintenance Information, Volume 1). Volume

1 contains information to help you Identify RS/6000 SP frame types and components, perform installa-
tion and relocation procedures, and maintenance agreements and qualifications.

IBM RS/6000 SP: Maintenance Information, Volume 3, Locations and Service Procedures
(GA22-7377), (referred to, throughout this publication, as

RS/6000 SP: Maintenance Information,

Volume 3). Volume 3 contains information to help you perform isolation and verification tests, identify
field replaceable unit (FRU) locations, and remove and replace FRUs.

IBM RS/6000 SP: Maintenance Information, Volume 4, Parts Catalog (GA22-7378), (referred to,
throughout this publication, as

RS/6000 SP: Maintenance Information, Volume 4). Volume 4 contains a

list of RS/6000 SP parts and FRUs with corresponding figures that contain indexed descriptions and
part numbers.

For a list of other SP books and related information, see the bibliography in the back of

RS/6000 SP:

Maintenance Information, Volume 1.

Who Should Use This Book

This book is intended for the product-trained Customer Engineer (CE). The procedures for RS/6000 SP
and feature components described in this book represent a part of the overall support structure of the
RS/6000 SP product. This book is intended to support the RS/6000 SP product and SP1/SP2 coexistence
systems, in which SP2 code is utilized. The SP1 version of this book (

IBM 9076 Scalable POWERparallel

Systems: Maintenance Information, SY66-0299) should be used for ordering SP1 parts, or if SP1 code is
utilized.

User's Responsibilities

Before calling the IBM customer engineer, the system administrator should use the problem determination
section of the

IBM Parallel System Support Programs for AIX: Diagnosis Guide, SC23-3866 for initial

problem determination. If there is nothing wrong with the customer operating procedures, customer-
supplied cables, or power source, the customer should call an IBM customer engineer.

How to Use This Book

When performing RS/6000 SP maintenance, follow Chapter 1, “Maintenance Analysis Procedures (MAPs)”
on page 1-1.

Beginning with the “MAP 0100: Start of Service Call” on page 1-4, isolate the problem to one or more of
these RS/6000 SP components:

Supervisor Subsystem



Copyright IBM Corp. 1994, 1999

xv

«
...
15
16
17
18
19
...
»

Summary of Contents for RS/6000 SP





































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands