Fuji Electric FRENIC-Ace series, User Manual

Page: 709 / 788

12.1 Standard Model
12-17
SP
EC
IF
IC
AT
IO
N
S
Chap 1
2
■
Standard-model, Single-phase 200 V (230 V) class series (HHD-mode: 0.1 kW to 2.2 kW)
Item Specifications
Type (FRN_ _ _ _E2S-7

) 0001 0002 0003 0005 0008 0011
Nominal applied motor (kW) [HP]
(Output rating) *1
0.1
[1/8]
0.2
[1/4]
0.4
[1/2]
0.75
[1]
1.5
[2]
2.2
[3]
O
utput r
ati
ngs
Rated capacity (kVA) *2
0.3
[0.3]
0.6
[0.6]
1.1
[1.2]
1.9
[2.0]
3.0
[3.2]
4.2
[4.4]
Rated voltage (V) * 3 Three-phase 200 to 240 V (with AVR function)
Rated current (A) * 4 0.8 1.6 3.0 5.0 8.0 11
Overload capability 150%-1 min, 200%-0.5 s
Input powe
r
Voltage, frequency Single-phase 200 to 240 V, 50/ 60 Hz
Allowable voltage/frequency Voltage: +10 to -10%, Frequency: +5 to -5%
Rated input current *7
(w/o DCR) (A)
1.8 3.3 5.4 9.7 16.4 24.8
(with DCR) (A) 1.1 2.0 3.5 6.4 11.6 17.5
Required capacity
(with DCR) (kVA) *8
0.3 0.4 0.7 1.3 2.4 3.5
B
rak
ing
Torque (%) *9 150% 100% 70% 40%
DC braking
Braking starting frequency: 0.0 to 60.0 Hz, Braking time: 0.0 to 30.0 s,
Braking level: 0 to 100%
Braking transistor Built-in as standard
Minimum resistance value ( Ω ) 100 40
Braking resistor Separately mounted option
DC reactor (DCR) Separately mounted option
Applicable safety standards IEC/EN61800-5-1: 2007
Enclosure (IEC60529) IP00, UL open type
Cooling method Natural cooling Fan cooling
Weight / Mass (kg) [lbs]
0.5
[1.1]
0.5
[1.1]
0.6
[1.3]
0.9
[2.0]
1.6
[3.5]
1.8
[4.0]
Note: A box (

) in the above table replaces GA, GB or C depending on the model.
*1 Fuji 4-pole standard motor
*2 Rated capacity is calculated assuming the rated output voltage as 220 V (230 V).
*3 Output voltage cannot exceed the power supply voltage.
*4 Setting the carrier frequency (F26) to the following value or above requires current derating.
HHD spec of type FRN0001 E2■ -4

to FRN0011 E2■ -4

: 8 kHz,
If reduction is necessary, for details, refer to Figure 10.4-1 in Chapter 10 “10.4.2 “Guideline for selecting
inverter drive mode and capacity.”
*7 This specification is an estimated value to be applied when the power supply capacity is 500 kVA (Inverter
capacity × 10 when the capacity exceeds 50 kVA) and the power supply with %X = 5% is connected.
*8 This specification applies when a DC reactor (DCR) is used.
*9 Average braking torque for the motor running alone. It depends on the efficiency of the motor.