Fuji Electric FRENIC-Ace series, User Manual

Page: 610 / 788

11.2 Currents Flowing Across the Inverter Terminals
11-6
Table 11.2-1 Currents Flowing across the Inverter Terminals (continued)
HHD mode (kW rating motor)
Power supply
voltage
Nominal
applied
motor
(kW)
Inverter type
50Hz, 200V/400V 60Hz, 220V/440V
Braking
resistor
circuit
current
(A)
Input RMS current (A) DC link
bus
current
(A)
Input RMS current (A) DC link
bus
current
(A)
DC reactors (DCRs) DC reactors (DCRs)
w/ DCR w/o DCR w/ DCR w/o DCR
Three-phase
200V/220V
0.1 FRN0001 E2■ -2

0.57 1.1 0.70 0.51 1.1 0.62 0.82
0.2 FRN0002 E2■ -2

0.93 1.8 1.1 0.85 1.7 1.0 1.2
0.4 FRN0004 E2■ -2

1.6 3.1 2.0 1.5 3.0 1.8 1.2
0.75 FRN0006 E2■ -2

3.0 5.3 3.7 2.8 5.0 3.4 1.6
1.5 FRN0010 E2■ -2

5.7 9.5 7.0 5.2 9.0 6.3 3.6
2.2 FRN0012 E2■ -2

8.3 13.2 10.2 7.6 12.3 9.3 3.5
3.7 FRN0020 E2■ -2

14.0 22.2 17.2 12.7 20.6 15.6 4.1
5.5 FRN0030E2 ■ -2

21.1 31.5 25.9 19.0 28.4 23.3 6.4
7.5 FRN0040E2 ■ -2

28.8 42.7 35.3 26.0 38.5 31.9 6.1
11 FRN0056E2 ■ -2

42.2 60.7 51.7 38.0 54.7 46.6 9.1
15 FRN0069E2 ■ -2

57.6 80.0 70.6 52.0 72.2 63.7 11
18.5 FRN0088E2■ -2

71.0 97.0 87.0 64.0 87.4 78.4 14
22 FRN0115E2■ -2

84.4 112 103 76.0 101 93.1 15
Three-phase
400V/440V
0.4 FRN0002 E2■ -4

0.85 1.7 1.0 0.74 1.7 0.99 0.80
0.75 FRN0004 E2■ -4

1.6 3.1 1.8 1.4 3.0 1.7 1.1
1.5 FRN0006 E2■ -4

3.0 5.9 3.5 2.6 5.1 3.2 1.8
2.2 FRN0007 E2■ -4

4.4 8.2 5.1 3.8 7.1 4.6 1.8
3.7 FRN0012 E2■ -4

7.3 13.0 8.6 6.4 11.1 7.8 2.1
5.5 FRN0022E2 ■ -4

10.6 17.3 13.0 9.6 15.7 11.8 3.2
7.5 FRN0029E2 ■ -4

14.4 23.2 17.7 13.0 21.0 16.0 3.1
11 FRN0037E2 ■ -4

21.1 33.0 25.9 19.0 29.8 23.3 4.5
15 FRN0044E2 ■ -4

28.8 43.8 35.3 26.0 39.5 31.9 5.7
18.5 FRN0059E2 ■ -4

35.5 52.3 43.5 32.0 47.1 39.2 7.2
22 FRN0072E2 ■ -4

42.2 60.6 51.7 38.0 54.6 46.6 7.7
30 FRN0085E2 ■ -4

57.0 77.9 69.9 51.4 70.2 63.0 10
37 FRN0105E2 ■ -4

68.5 94.3 83.9 61.8 85.0 75.7 12
45 FRN0139E2 ■ -4

83.2 114 102 75.0 103 91.9 15
55 FRN0168E2 ■ -4

102 140 125 91.9 126 113 19
75 FRN0203E2 ■ -4

138 - 169 124 - 152 24
90 FRN0240E2 ■ -4

164 - 201 148 - 181 31
110 FRN0290E2 ■ -4

201 - 246 181 - 222 35
132 FRN0361E2 ■ -4

238 - 292 214 - 263 42
160 FRN0415E2 ■ -4

286 - 350 258 - 315 50
200 FRN0520E2 ■ -4

357 - 437 321 - 394 62
220 FRN0590E2 ■ -4

390 - 478 351 - 430 71
Single-phase
200V
0.1 FRN0001E2■ -7

1.1 1.8 1.1 1.0 1.8 1.0 0.61
0.2 FRN0002E2■ -7

2.0 3.3 2.0 1.8 3.1 1.8 0.66
0.4 FRN0003 E2■ -7

3.5 5.4 3.5 3.1 5.0 3.1 0.82
0.75 FRN0005 E2■ -7

6.4 9.7 6.4 5.8 9.1 5.8 1.4
1.5 FRN0008 E2■ -7

11.6 16.4 12 10.5 15.5 10.5 1.4
2.2 FRN0011 E2■ -7

17.5 24.8 18 15.8 23.4 15.8 1.7
Note: A box (■) in the above table replaces S (Basic type) or E (EMC filter built-in type) depending on the enclosure.
A box (

) in the above table replaces GA, GB or C depending on the model.
• Inverter efficiency is calculated using values suitable for each inverter model. The input route mean square
current is calculated based on a power supply capacity of 500 kVA (or 10 times as large as the inverter’s
capacity when the inverter’s capacity exceeds 50 kVA), and a power supply reactance of 5%.
• The input RMS current listed in the above table will vary in inverse proportion to the power supply voltage, such
as 480 VAC.
• The braking current is always constant, independent of braking resistor specifications, including standard and
10%ED models.