Fuji Electric FRENIC-Ace series, User Manual

Page: 640 / 788

11.9 Power Regenerative PWM Converters, RHC Series
11-36
11.9.3 Function specifications
■
Terminal functions
Cl
as
si
fi
-c
ati
on
Symbol Name Functions
M
ai
n c
irc
ui
t
L1/R, L2/S, L3/T Main circuit power
inputs
Connects with the three-phase input power lines through a dedicated
reactor.
P(+), N(-) Converter outputs Connects with the power input terminals P(+) and N(-) on an inverter.
ok Grounding Grounding terminal for the converter’s chassis (or enclosure).
R0, T0
Auxiliary power input for
the control circuit
For the backup of the control circuit power supply, connect the power lines
same as that of the main power input.
Vol
tage
detec
tion R1, S1, T1
Synchronous power
input for voltage
detection
Voltage detection terminals for the internal control of the converter. Connect
with the power supply side of the dedicated reactor or filter.
R2, T2
Inputs for control
monitoring
Detection terminal for AC fuse blown.
Input s
ignal
[RUN] Run command
Short-circuiting terminals [RUN] and [CM] runs the converter; opening them
stops the converter.
[RST] Reset alarm command
When the converter stops due to an alarm, removing the alarm factor and
short-circuiting the terminals [RST] and [CM] cancels the protective
function, restarting the converter.
[X1]
General-purpose
transistor input
0: Enable external alarm trip THR
1: Cancel current limiter LMT-CCL
2: 73 answerback 73ANS
3: Switch current limiter I-LIM
4: Option DI OPT-DI
[CM] Digital input common Common terminal for digital input signals.
[PLC] PLC signal power
Connects to PLC output signal power supply. (Rated voltage: 24 VDC (22 to
27 VDC)
O
utput s
ignal
[30A/B/C]
Alarm relay output
(for any alarm)
Outputs a signal when the protective function is activated to stop the
converter.
(Contact: [1C], Terminals [30A] and [30C] are closed: Signal ON) (Contact
rating: 250 VAC, max. 50 mA)
[Y1], [Y2], [Y3],
[Y11] to [Y18]
General-purpose
transistor output
0: Converter running RUN
1: Converter ready to run RDY
2: Power supply current limiting IL
3: Lifetime alarm
LIFE
4: Heat sink overheat early warning PRE-OH
5: Overload early warning PRE-OL
6: Power running DRV
7: Regenerating REG
8: Current limiting early warning CUR
9: Restarting after momentary power failure U-RES
10: Synchronizing power supply frequency SY-HZ
11: Alarm content 1 AL1
12: Alarm content 2
AL2
13: Alarm content 4 AL4
14: Option DO OPT-DO
* Mounting the OPC-VG7-DIOA option makes 8 points of DO extended
functions available. (DI functions are not available.)
[CME] Digital output common
[Y5A/C] Relay output
[A01], [A04],
[A05]
General-purpose
analog output
0: Input power PWR
1: Input current in RMS I-AC
2: Input voltage in RMS V-AC
3: DC link bus voltage V-DC
4: Power supply frequency FREQ
5: +10 V test P10
6: -10 V test N10
* Mounting the OPC-VG7-AIO option makes 2 points of AO extended
functions available. (AI functions are not available.)
[M] Analog output common Common terminal for analog output signal.
[73A], [73C]
Charging resistor input
relay outputs
Control output for the input relay of the external charging resistor (73).