COBHAM GR740 User Manual Download Page 317

Page: 317 / 488

GR740-UM-DS, Nov 2017, Version 1.7

317

www.cobham.com/gaisler

GR740

22.3

Registers

The core is programmed through registers mapped into APB address space.

Table 400.

General Purpose I/O Port registers

APB address offset

Register

0x00

I/O port data register

0x04

I/O port output register

0x08

I/O port direction register

0x0C

Interrupt mask register

0x10

Interrupt polarity register

0x14

Interrupt edge register

0x18

Reserved

0x1C

Capability register

0x20

Interrupt map register 0

0x24

Interrupt map register 1

0x28

Interrupt map register 2

0x2C

Interrupt map register 3

0x30 - 0x3C

Reserved

0x40

Interrupt available register

0x44

Interrupt flag register

0x48

Reserved

0x4C

Pulse register

0x50

Reserved

0x54

I/O port output register, logical-OR

0x58

I/O port direction register, logical-OR

0x5C

Interrupt mask register, logical-OR

0x60

Reserved

0x64

I/O port output register, logical-AND

0x68

I/O port direction register, logical-AND

0x6C

Interrupt mask register, logical-AND

0x70

Reserved

0x74

I/O port output register, logical-XOR

0x78

I/O port direction register, logical-XOR

0x7C

Interrupt mask register, logical-XOR

Summary of Contents for GR740









































































































































































































































































































































































































































































































Search results

Summary of Contents for GR740

Reviews:

Related manuals for GR740

Brands by name

Popular brands

COBHAM GR740, User Manual

Search results

Summary of Contents for GR740

Reviews:

Related manuals for GR740

Brands by name

Popular brands