manualshive.com logo in svg

COBHAM GR740, User Manual

The COBHAM GR740 User Manual is available for free download from our website. This comprehensive manual provides step-by-step instructions on how to make the most of your GR740 device. Get your hands on the manual today and unlock the full potential of your product.

Share
Download
background image

GR740-UM-DS, Nov 2017, Version 1.7

278

www.cobham.com/gaisler

GR740

17.9.16 Receive Channel Read Register [CanRxRD]

Table 355.

0x310 - CanRxRD - Receive Channel Read Register

The field is implemented as relative to the buffer base address (scaled with the SIZE field).
The READ field is written to in order to release the receive buffer, indicating the po1 of the 
last message that has been read out.
Note that it is not possible to fill the buffer. There is always one message position in buffer unused. 
Software is responsible for not over-reading the buffer on wrap around (i.e. setting WRITE=READ).

17.9.17 Receive Channel Interrupt Register [CanRxIRQ]

Table 356.

0x314 - CanRxIRQ - Receive Channel Interrupt Register

Note that this indicates that a programmed number of messages have been received.
The field is implemented as relative to the buffer base address (scaled with the SIZE field).

17.9.18 Receive Channel Mask Register [CanRxMASK]

Table 357.

0x318 - CanRxMASK - Receive Channel Mask Register

Note that Base ID is bits 28 to 18 and Extended ID is bits 17 to 0.

17.9.19 Receive Channel Code Register [CanRxCODE]

Table 358.

0x31C - CanRxCODE - Receive Channel Code Register

Note that Base ID is bits 28 to 18 and Extended ID is bits 17 to 0.

31

20 19

4

3

0

READ

0

rw

19: 4

READ - Pointer to last read m1

31

20 19

4

3

0

IRQ

0

rw

19: 4

IRQ - Interrupt is generated when CanRxWR.WRITE=IRQ, as a consequence of a message recep-
tion

31

29 28

0

AM

0x1FFFFFFF

rw

28: 0

Acceptance Mask (AM) - Bits set to 1b are taken into account in the comparison between the 
received message ID and the CanRxCODE.AC field

31

29 28

0

AC

0

rw

28: 0

Acceptance Code (AC) - Used in comparison with the received message

Summary of Contents for GR740









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GR740

ZALMAN CNPS17X User Manual preview
CNPS17X
Brand: ZALMAN Pages: 20
Paradyne FrameSaver 9120 Installation Instruction Supplement preview
FrameSaver 9120
Brand: Paradyne Pages: 2
Omega Engineering OME-A8111 Hardware Manual preview
OME-A8111
Brand: Omega Engineering Pages: 34
IDT USB-BRIDGEV2-EVAL Evaluation Board Manual preview
USB-BRIDGEV2-EVAL
Brand: IDT Pages: 11
Vega ARIES v3.0 Product Reference Manual preview
ARIES v3.0
Brand: Vega Pages: 12
IceTech POD-51EH-C541U-12 Operating Instructions Manual preview
POD-51EH-C541U-12
Brand: IceTech Pages: 8
Intel IXP28 Series Manual preview
IXP28 Series
Brand: Intel Pages: 154
Paradyne iMarc SLV 9820-2M Installation Instructions Manual preview
iMarc SLV 9820-2M
Brand: Paradyne Pages: 24
SilverStone SDP12 Quick Start Manual preview
SDP12
Brand: SilverStone Pages: 2
Abocom WM5504 User Manual preview
WM5504
Brand: Abocom Pages: 70
Abus TVAC21000 User Manual preview
TVAC21000
Brand: Abus Pages: 98
AXIOMTEK tBOX312-870-FL Quick Installation Manual preview
tBOX312-870-FL
Brand: AXIOMTEK Pages: 2
Dahua Technology VDA-NVR2108W4KS2 User Manual preview
VDA-NVR2108W4KS2
Brand: Dahua Technology Pages: 363
Azoteq IQ Switch IQS128 Connection Manual preview
IQ Switch IQS128
Brand: Azoteq Pages: 4
Orcomm DILX-GW Operation Manual preview
DILX-GW
Brand: Orcomm Pages: 10
Johnson Controls Metasys NAE55 Installation Manual preview
Metasys NAE55
Brand: Johnson Controls Pages: 20
Cirrus Logic Crystal CS98000 Series Manual preview
Crystal CS98000 Series
Brand: Cirrus Logic Pages: 40
StarTech.com USBDUP12 User Manual preview
USBDUP12
Brand: StarTech.com Pages: 20

Brands by name

Popular brands

Load more brands