manualshive.com logo in svg

COBHAM GR740, User Manual

The COBHAM GR740 User Manual is available for free download from our website. This comprehensive manual provides step-by-step instructions on how to make the most of your GR740 device. Get your hands on the manual today and unlock the full potential of your product.

Share
Download
background image

GR740-UM-DS, Nov 2017, Version 1.7

184

www.cobham.com/gaisler

GR740

Table 177. 

0x00000800 - RTR.PCTRLCFG - Port control, port 0 (configuration port)

31

18 17 16 15

10

9

8

0

RESERVED

PL TS

RESERVED

TR

RESERVED

0x0000

0

0

0x00

1

0x000

r

rw rw

r

rw

r

31: 18

RESERVED

17

Packet length truncation (PL) - When set to 1, an RMAP / SpaceWire Plug-and-Play reply is spilled, and an EEP 
written to the transmit FIFO of the output port, if the total length of the reply packet exceeds the maximum 
length specified in the RTR.MAXPLEN register for port 0. See section 13.2.16 for more information on packet 
length truncation.

16

Time-code / distributed interrupt code truncation (TS) - When set to 1, an ongoing RMAP / SpaceWire Plug-
and-Play reply is spilled, and an EEP written to the transmit FIFO of the output port, if a valid time-code or dis-
tributed interrupt code is received, and if the time-code / distribute interrupt code matches the codes selected by 
the RTR.PCTRL2CFG.SV and RTR.PCTRL2CFG.SM fields. See section 13.2.21 for more information on time-
code / distributed interrupt code spill.

15: 10

RESERVED

9

Timer enable (TR) - Enable data character timer for port 0. See section 13.2.15 for details.

8: 0

RESERVED

Table 178. 

0x00000804-0x00000830 - RTR.PCTRL - Port control, ports 1-12 (SpaceWire ports and AMBA ports)

31

24 23 22 21 20 19 18 17 16 15 14

11 10

9

8

7

6

5

4

3

2

1

0

RD

RES

ST SR AD LR PL TS IC ET RESERVED DI TR PR TF RS TE R CE AS LS LD

0x27

0x0

0

0

0

0

0

0

*

0

0x0

0

1

0

0

0

1

0

1

1

0

0

rw

r

rw rw rw rw rw rw rw rw

r

rw rw rw rw rw rw

r

rw rw rw rw

31: 24

Run-state clock divisor (RD) - Clock divisor value used for the corresponding port’s link interface when in run-
state. Field is only available for the SpaceWire ports.

23: 22

RESERVED

21

Static routing enable (ST) - When set to 1, incoming packets on this port are routed based on the physical 
address specified in the corresponding RTR.PCTRL2.SD field, and the setting of the corresponding 
RTR.PCTRL2.SC bit, instead of the packet’s first byte. Header deletion is not used when static routing is 
enabled, which means that the first byte of the packet is always sent as well. This bit can only be set to 1 if the 
RTR.RTRCFG.SR bit is set to 1. Note that when this bit is set to 1 it is not possible to access the configuration 
port from this port.

20

Spill-if-not-ready (SR) - This bit is double mapping of the RTR.RTACTRL.SR bit. See table 176.

19

Auto-disconnect (AD) - When set to 1, the auto-disconnect feature described in section 13.2.14 is enabled. This 
bit is only available for the SpaceWire ports.

18

Link-start-on-request (LR) - When set to 1, the link-start-on-request feature described in section 13.2.13 is 
enabled. This bit is only available for the SpaceWire ports.

17

Packet length truncation (PL) - When set to 1, packets for which this port is the input port will be spilled, and an 
EEP written to the transmit FIFO of the output port(s) if the packets exceed the maximum length specified in the 
corresponding RTR.MAXPLEN register. See section 13.2.16 for more information on packet length truncation.

16

Time-code / distributed interrupt code truncation (TS) - When set to 1, ongoing packets for which this port is the 
input port will be spilled, and an EEP written to the transmit FIFO of the output port(s), if a valid time-code / 
distributed interrupt code is received, and if the time-code / distributed interrupt code also matches the codes 
selected by the RTR.PCTRL2.SV and RTR.PCTRL2.SM fields. See section 13.2.21 for more information on 
time-code / distributed interrupt code spill.

15

Distributed interrupt codes enable (IC) - When set to 0, all incoming distributed interrupt codes on this port are 
discarded, and no distributed interrupt codes are sent out on the port. When set to 1, the four bits 
RTR.PCTRL2.IR, RTR.PCTRL2.IT, RTR.PCTRL2.AR, RTR.PCTRL2.AT are used to enable / disable distrib-
uted interrupt code transmit and receive. Note that the global distributed interrupt code enable bit, RTRTCFG.IE, 
also must be set to 1 for distributed interrupt codes to be sent / received. See section 13.2.18 for a description of 
distributed interrupt code distribution. Reset value depends on bootstrap signals, as described in section 3.1.

Summary of Contents for GR740









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GR740

FabiaTech FX5638 Series Users Quick Reference preview
FX5638 Series
Brand: FabiaTech Pages: 4
Laurell WS-650 lite Series Operation Manual preview
WS-650 lite Series
Brand: Laurell Pages: 84
Parker PCH1 T P Series User Manual preview
PCH1 T P Series
Brand: Parker Pages: 107
Intel IXP45X Developer'S Manual preview
IXP45X
Brand: Intel Pages: 958
Anthem Audio SFD-2 MkIII Jumper Configurations preview
SFD-2 MkIII Jumper
Brand: Anthem Audio Pages: 2
ASROCK H670M PRO RS Manual preview
H670M PRO RS
Brand: ASROCK Pages: 173
Rosewill RCX-Z5 User Manual preview
RCX-Z5
Brand: Rosewill Pages: 2
ADTRAN 1200864L1 Quick Start Manual preview
1200864L1
Brand: ADTRAN Pages: 2
Aim ACE1553-3U-4 Hardware Manual preview
ACE1553-3U-4
Brand: Aim Pages: 35
SIIG US2273 Quick Installation Manual preview
US2273
Brand: SIIG Pages: 8
Xilinx DPU IP Product Manual preview
DPU IP
Brand: Xilinx Pages: 43
Extreme Networks ACC-BKT-AX-BEAM Accessories Manual preview
ACC-BKT-AX-BEAM
Brand: Extreme Networks Pages: 35
NEC N8151-53 User Manual preview
N8151-53
Brand: NEC Pages: 114
Eneo PNR-5332/3TB Quick Installation Manual preview
PNR-5332/3TB
Brand: Eneo Pages: 49
Infrant Technologies READYNAS X6 Installation Manual preview
READYNAS X6
Brand: Infrant Technologies Pages: 2
EZCast M2 User Manual preview
M2
Brand: EZCast Pages: 27
Pico Macom SC-3 Installation And Operation Manual preview
SC-3
Brand: Pico Macom Pages: 4
Johnson Controls FIRE-MON-17 Technical Manual preview
FIRE-MON-17
Brand: Johnson Controls Pages: 72

Brands by name

Popular brands

Load more brands