manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 234 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 234

e-STUDIO477S/527S/477SL

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

REPLACEMENT OF PC BOARDS/HDD

6 - 20

[D] Restore encryption key

Notes: 

If turning the power ON while pressing [3] and the [CLEAR] button simultaneously or restoring 
the key is not possible, update the system firmware using the download jig, and then perform this 
procedure again.

 P. 8-18 "8.3 Firmware Updating with PWA-DWNLD-JIG2"

(1) Turn the power ON while pressing [3] and the [CLEAR] button simultaneously.

(2) Enter the password, and then press the [OK] button. (If the password is not set for Service, press 

the [OK] button without entering anything.)

(3) Key in [5] to select "5. Key Backup Restore", and then press the [START] button.

(4) Key in [1] to select "1. Key SRAM to FROM", and then press the [START] button.

(5) Wait until the restoring of the encryption key is completed. "Operation Complete" is displayed.

(6) Restart the equipment after the restoring is completed. If you want to perform the restoring of the 

license, do not restart the equipment but perform from (4) in "[H] Restore license".

[E] Restore license

Notes: 

If turning the power ON while pressing [3] and the [CLEAR] button simultaneously or restoring 
the license is not possible, update the system firmware using the download jig, and then perform 
this procedure again.

 P. 8-18 "8.3 Firmware Updating with PWA-DWNLD-JIG2"

(1) Turn the power ON while pressing [3] and the [CLEAR] button simultaneously.

(2) Enter the password, and then press the [OK] button. (If the password is not set for Service, press 

the [OK] button without entering anything.)

(3) Key in [5] to select "5. Key Backup Restore", and then press the [START] button.

(4) Key in [3] to select "3. License SRAM to FROM", and then press the [START] button.

(5) Wait until the restoring of the license is completed. "Operation Complete" is displayed.

(6) After the restoring is completed, check that "OK" is indicated in "SRAM License STATUS" and 

"FROM License Status". Then, restart the equipment.

(7) If "4. License FROM to SRAM" is performed by mistake, carry out the following procedure.

 P. 6-30 "[ 1 ] Re-registration when the board is replaced"

[F] Update firmware version

(1) Update the version of system firmware using the USB device.

 P. 8-4 "8.2 Firmware Updating with a USB Device"

[G] Reinstall license

If the license was returned in "[A]Return License", reinstall it with the following procedure.

(1) Turn the power ON while pressing [0] and [8] simultaneously.

(2) Enter the password, and then press the [OK] button.

(If the password is not set for Service, press the [ENTER] button without entering anything.)

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов