Toshiba e-Studio477s Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 482

Toshiba e-Studio477s Скачать руководство пользователя страница 98

e-STUDIO477S/527S/477SL

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

SETTING / ADJUSTMENT

4 - 18

4.4.6

Sharpness adjustment

If you want to make scan images look softer or sharper, perform the following adjustment. The
adjustment can be made for each of the color modes and original modes independently.

<Adjustment Mode (05)>

Notes:

You have to make adjustment by balancing between moire and sharpness.

<Procedure>
The procedure is the same as that of

P. 4-15 "4.4.2 Density adjustment".

4.4.7

Fine adjustment of black density

The density of black side on scanned image is adjusted at color-scanning.

<Adjustment Mode (05)>

Notes:

Be careful for the value not to be too large since the gradation is reproduced worse in darker
side.

<Procedure>

(1) While pressing [0] and [5] simultaneously, turn the power ON.
(2) Key in the codes and press the [START] button.
(3) Key in the adjustment values. Acceptable values: 0 to 4. (To correct the value once keyed in,

press the [CLEAR] button.)

(4) Press the [OK] or [INTERRUPT] button to store the value in memory.



The equipment goes

back to the ready state.

(5) Let the equipment restart and perform the scanning job.
(6) If the desired image has not been attained, repeat step (1) to (5).

Code

Color mode

Original mode

Contents

8354

Full Color

Text/Photo

The larger the value is, the sharper the image
becomes; while the smaller the value is, the softer
the image becomes.
The smaller the value is, the less moire tends to
appear.
The acceptable values are 0 to 255.
The center value is 128.

8335

Text

8336

Photo

8375

Custom mode

7430

Black

Text/Photo

7431

Text

7432

Photo

7470

Custom mode

7433

Gray Scale

-

Code

Original mode

Remarks

8314

Text/Photo

The larger the value is, the black side of the image becomes darker.
Acceptable values: 0 to 4 (Default: 1)

8315

Text

The larger the value is, the black side of the image becomes darker.
Acceptable values: 0 to 4 (Default: 0)

8316

Photo

8371

Custom mode

«
...
96
97
98
99
100
...
»

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов