Toshiba e-Studio477s Скачать руководство пользователя страница 146

Страница: 146 / 482

e-STUDIO477S/527S/477SL

ERROR CODE AND TROUBLESHOOTING

5 - 42

[F110] Communication error between System-CPU and Scanner-CPU
[F111] Scanner response abnormality

Check firmware version

• Check the version of the system firmware on the SYS

board.

• Check the version of the PU firmware on the PU

board.

Board check

• Check if the connector CN118, CN119 on the SYS

board and the connector CUIF0, CUIF1 on the PU
board are completely inserted.

• Check if the connector pin between the SYS board

(connector CN118, CN119) and the PU board
(connector CUIF0, CUIF1) is disconnected.

• Check if the connectors HEAD0K of the LED head is

completely inserted, and the harness is disconnected
or open circuited.

• Check if the conductor patterns on the PU board and

SYS board are short circuited or open circuited

Parts to be replaced

Remark

PU board
SYS board
LED head
Harness of LED head

Classification

Error content

Communication related service
call

[F110] Communication error between System-CPU and Scanner-
CPU
[F111] Scanner response abnormality

Check item

Measures

SU board

• Check if the harness connecting the SU board and SYS board is

disconnected or open circuited.

• Check if the conductor pattern on the SU board is short circuited

or open circuited.

SYS board

Check if the conductor pattern on the SYS board is short circuited or
open circuited.

Parts to be replaced

Remark

SU board
SYS board

Procedure

Check item

Measures

Содержание e-Studio477s


























































































































































































































































































































































































































































































Результаты поиска

Содержание e-Studio477s

Отзывы:

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 146 / 482

Результаты поиска

Содержание e-Studio477s

Отзывы: