Toshiba e-Studio477s Скачать руководство пользователя страница 203

Страница: 203 / 482

e-STUDIO477S/527S/477SL

ERROR CODE AND TROUBLESHOOTING

5 - 99

5.3.12

Network error

[8000] Static IPv4 address conflict

[8011] Linklocal Address Conflict

[8012] Manual Address Conflict

[8013] Stateless Address Conflict

[8014] Stateful Address Conflict

[8022] Authentication Failure

Classification

Error item

Network error

IPv4 address overlaps.

Check item

Measures

Setting

Check if the same IP address is not used by other machine.

Classification

Error item

Network error

Linklocal Address Conflict

Check item

Measures

Setting

Check if the same IP address is not used by other machine.

Classification

Error item

Network error

Manual IPv6 Address Conflict

Check item

Measures

Setting

Check if the same IP address is not used by other machine.

Classification

Error item

Network error

Stateless Address Conflict

Check item

Measures

Setting

Check if the same IP address is not used by other machine.

Classification

Error item

Network error

Stateful Address Conflict

Check item

Measures

Setting

Check if the same IP address is not used by other machine.

Classification

Error item

Network error

Failed in 802.1X authentication.

Check item

Measures

Setting

Check the user credential.

Содержание e-Studio477s


























































































































































































































































































































































































































































































Результаты поиска

Содержание e-Studio477s

Отзывы:

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 203 / 482

Результаты поиска

Содержание e-Studio477s

Отзывы: