Toshiba e-Studio477s Скачать руководство пользователя страница 93

Страница: 93 / 482

e-STUDIO477S/527S/477SL

SETTING / ADJUSTMENT

4 - 13

4.3.4

Density adjustment of graphic lines (1200 dpi)

This adjustment is available regardless of whether "Distinguish Thin Lines" of the printer driver is
selected or not.

Notes:

Be sure to set the values of the upper and lower limit properly so that they are not set in reverse.

<Procedure>
The procedure is the same as that of



P. 4-11 "4.3.1 Gamma balance adjustment (Black Mode)".

Color mode

Code

Remarks

Black

8242-0

The density of the line in Black in the line density range specified

by "05-8243-0" or "05-8243-1" can be adjusted.

The larger the value is, the darker the line density becomes.

Acceptable value: 0 to 5 (Default: 4)

Color mode

Code

Remarks

Black

8243-0

The effective range (lower limit) of the

density adjustment for the line in Black can

be set.

Acceptable value: 0 to 255 (Default: 1)

The density range

selected in the

upper and lower

limit is adjusted with

05-8242-0.

8243-1

The effective range (upper limit) of the

density adjustment for the line in Black can

be set.

Acceptable value: 0 to 255 (Default: 200)

Содержание e-Studio477s


























































































































































































































































































































































































































































































Результаты поиска

Содержание e-Studio477s

Отзывы:

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 93 / 482

Результаты поиска

Содержание e-Studio477s

Отзывы: