Toshiba e-Studio477s Скачать руководство пользователя страница 136

Страница: 136 / 482

e-STUDIO477S/527S/477SL

ERROR CODE AND TROUBLESHOOTING

5 - 32

[EA50] Stapling jam

[EA60] Early arrival jam

Finisher control PC board

Classification

Error content

Paper jam in finisher section

Staple jam occurred at stapler.

Check item

Measures

Stapler

• Remove the staple cartridge, remove any jammed staples, install

the staple cartridge.

• Connector check (P9-1, P10-1)
• Harness check

Finisher control PC board

• Board check
• Connector check (J9, J10)
• Harness check

Parts to be replaced

Remark

Stapler
Finisher control PC board

Classification

Error content

Paper jam in finisher section

The entrance path sensor detects the paper earlier than a specified
timing.

Check item

Measures

Entrance transport sensor
abnormality

• Replace the entrance transport sensor

Faulty cables and connectors

• Check if the electrical continuity between the connector

terminals is normal. If electricity is not conducted, replace the
connector. (Finisher control PC board: J7)

Finisher control PC board
abnormality

• If the error still occurs after replacing the sensor and the

connector, exchange the finisher control PC board.

Parts to be replaced

Remark

Entrance transport sensor
Finisher control PC board

Parts to be replaced

Remark

Содержание e-Studio477s


























































































































































































































































































































































































































































































Результаты поиска

Содержание e-Studio477s

Отзывы:

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 136 / 482

Результаты поиска

Содержание e-Studio477s

Отзывы: