Toshiba e-Studio477s Скачать руководство пользователя страница 208

Страница: 208 / 482

e-STUDIO477S/527S/477SL

ERROR CODE AND TROUBLESHOOTING

5 - 104

[8043] IPsec IKE version mismatch

[8044] IPsec encaptulation mismatch

[8045] IPsec Peer IP mismatch

[8046] IPsec local IP mismatch

[8047] IPsec local ID mismatch

[8048] IPsec Remote ID mismatch

Classification

Error item

Network error

Ipsec error if ike version is not matching

Check item

Measures

Setting

Mismatch in IKE version.
Check the IKE version in MFP and peer.

Classification

Error item

Network error

Ipsec error for encaptulation is not matching

Check item

Measures

Setting

Check the IPsec mode (Transport/Tunnel) in MFP and peer.

Classification

Error item

Network error

Ipsec error for peer ip mismatch

Check item

Measures

Setting

Remote Traffic selector mismatch.
Check the destination address/port in IPsec filter.

Classification

Error item

Network error

Ipsec error for local ip mismatch

Check item

Measures

Setting

Local traffic selector mismatch.
Check the source address/port in IPsec filter.

Classification

Error item

Network error

Ipsec error for local id mismatch

Check item

Measures

Setting

Check the user certificate in MFP

Classification

Error item

Network error

Ipsec error for remote id mismatch

Check item

Measures

Setting

Check the user certificate in peer machine.

Содержание e-Studio477s


























































































































































































































































































































































































































































































Результаты поиска

Содержание e-Studio477s

Отзывы:

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 208 / 482

Результаты поиска

Содержание e-Studio477s

Отзывы: