Toshiba e-Studio477s Скачать руководство пользователя страница 134

Страница: 134 / 482

e-STUDIO477S/527S/477SL

ERROR CODE AND TROUBLESHOOTING

5 - 30

[EA2A] Paper transport jam (Between entrance transport and exit transport)

[EA2B] Paper transport jam (Exit transport sensor)

Entrance transport sensor

• Sensor check (S1)
• Connector check (P7-2)
• Harness check

Exit transport sensor

• Sensor check (S2)
• Connector check (P8-1)
• Harness check

Finisher control PC board

• Board check
• Connector check (J7,J8) J7: input, J8: output
• Harness check

Parts to be replaced

Remark

Entrance transport sensor
Exit transport sensor
Finisher control PC board

Classification

Error content

Paper jam in finisher section

Leading edge of paper in finisher transport path passed entrance
transport sensor, but did not arrive at exit transport sensor.

Check item

Measures

Transport path

If there is paper in the paper transport path, remove the paper.

Entrance transport sensor

• Sensor check (S1)
• Connector check (P7-2)
• Harness check

Exit transport sensor

• Sensor check (S2)
• Connector check (P8-1)
• Harness check

Finisher control PC board

• Board check
• Connector check (J7,J8) J7: input, J8: output
• Harness check

Parts to be replaced

Remark

Entrance transport sensor
Exit transport sensor
Finisher control PC board

Classification

Error content

Paper jam in finisher section

Paper stayed for longer than set period at exit transport sensor
while being transported in finisher transport path.

Check item

Measures

Transport path

If there is paper in the paper transport path, remove the paper.

Exit transport sensor

• Sensor check (S2)
• Connector check (P8-1)
• Harness check

Check item

Measures

Содержание e-Studio477s


























































































































































































































































































































































































































































































Результаты поиска

Содержание e-Studio477s

Отзывы:

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 134 / 482

Результаты поиска

Содержание e-Studio477s

Отзывы: