manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 122 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 122

e-STUDIO477S/527S/477SL

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

ERROR CODE AND TROUBLESHOOTING

5 - 18

4411

Image data creation failure: Data that you tried to print may be 
corrupted.
• Network print: Data are corrupted or invalid.
• Direct print: A file is corrupted or not in a supported format.

P. 5-84

4412

Double-sign encoding error: A double-sign encoding error occurred 
because the PDF file is encrypted in a forbidden language or in a 
language not supported.

P. 5-84

4611

Font download failure (exceeding maximum number of registrations): 
A new font cannot be registered because the number of fonts 
registered in this equipment has reached the limit.

P. 5-84

4612

Font download failure (HDD full): A new font cannot be registered 
because there is not sufficient space in the font storage area of this 
equipment.

P. 5-84

4613

Font download failure (others): A new font cannot be registered due 
to other abnormality.

P. 5-84

4621

Font deletion failure: A font cannot be deleted because the specified 
font does not exist, the specified font is undeletable or any other 
abnormality occurred.

P. 5-84

4F10

Printing was not performed successfully due to other abnormalities.

P. 5-84

Error code

Contents

Troubleshooting

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов