manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 164 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 164

e-STUDIO477S/527S/477SL

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

ERROR CODE AND TROUBLESHOOTING

5 - 60

[F109_3] Key consistency error (HDD encryption parameter damage)

Take measures given in the following table according to the messages displayed in the SRAM Key 
Status and FROM Key Status fields. 

Remarks: 

If the error is not cleared, reinstallation of the system firmware, system software and application 
is needed. ([4]+[9] 



Power-ON)

Check item

Measures

Setting

Reboot the equipment.
If it cannot be recovered, reinstall the software in the 
following procedure.
1. Install the system firmware.
2. If the error cannot be solved after installing the system 

firmware, reinstall the system software and application 
program.

 P. 8-7 "8.2.4 Update procedure"([A]Updating firmware)

Classification

Contents

Other service call

Key consistency error - Parameter used for HDD partition 
encryption are damaged.

Check item

Measures

Encryption key status confirmation

Check the message displayed by [3] + [C] + [POWER] 

 5. 

Key Backup Restore.

SRAM Key 

Status

FROM Key 

Status

Measure

*

AccessFailed

Replace the SYS board.

 P. 6-18 "6.2.4 Precautions and Procedures when replacing 

the SYS board" (all steps)
<With USB backup data: All key data recovery>
1. Recover all the data on the SRAM board.

[5] + [9] + [POWER] 

 2. Restore SRAM Data from USB

(For details, see "9.1.4Cloning procedure [B]Restore 
procedure")

2. Recover the encryption key/license on the SYS board.

Follow the procedures below noted in "6.2.4Precautions 
and Procedures when replacing the SYS board".
[C] Restore ADI key (only when ADI-HDD is installed)
[D] Restore encryption key
[E] Restore license

AccessFailed

*

Replace the SYS board.

 P. 6-22 "6.2.5 Precautions and procedure when replacing 

the SRAM board (for the SYS board)" (for the SYS board, all 
steps)

OK

KeyNull/
KeyBroken

Recover the encryption key on the SYS board.

 P. 6-18 "6.2.4 Precautions and Procedures when replacing 

the SYS board" ([D]Restore encryption key)

AccessFailed

OK

Replace the SRAM board (for the SYS board).

 P. 6-22 "6.2.5 Precautions and procedure when replacing 

the SRAM board (for the SYS board)" (all steps)

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов