Toshiba e-Studio477s Скачать руководство пользователя страница 448

Страница: 448 / 482

Maintenance Utility Operating Manual 42678819FU02 - 12/38

2.3.2

The main window includes the following menu commands:

(1)

File(F)
i.

Exit(X)

(2)

View(V)
i.

Tool Bar(T)

(3)

Tool(T)
i.

Printer Discovery(D)

ii.

Setting (S)

(4)

Help(H)
i.

Help Topics(H)

ii.

About MuWin(A)

iii.

Support Models(S)

No.

Description of function

(1)-i

Shuts down Maintenance Utility.

(2)-i

Shows or hides the toolbar.

(3)-i

Displays the printer search/connection window to enable a printer search/reconnect.

(3)- ii

Makes various Maintenance Utility settings (see section 2.3.3.1 for details).

(4)-i

Displays the Maintenance Utility Help window.

(4)-ii

Displays the version information for Maintenance Utility and related modules.

(4)-iii

Displays the names of printer models supported by Maintenance Utility.

2.3.3

Toolbar

Click the icons on the toolbars of the main window to run the commands specified below.

Icon

(L to R)

Description of function

Displays the printer search/connection window to allow a printer search/reconnect (same as command
(3)-i in 2.3.2)

Displays the version information for Maintenance Utility and related modules (same as command (4)-ii
in 2.3.2)

Содержание e-Studio477s


























































































































































































































































































































































































































































































Результаты поиска

Содержание e-Studio477s

Отзывы:

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 448 / 482

Результаты поиска

Содержание e-Studio477s

Отзывы: