manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 235 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 235

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO477S/527S/477SL

REPLACEMENT OF PC BOARDS/HDD

6 - 21

6

(3) Key in [3840], and then press the [START] button.

(4) Press the [INSTALL] button.

(5) Install the one-time dongle in the equipment (the one which you used for returning the selected 

license before replacing the equipment). Then press the [OK] button.

(6) Select the license to be installed, and then press the [INSTALL] button.

(7) The screen for notifying that the installation will be started is displayed. Then press the [YES] 

button.

(8) After 10 to 40 seconds have passed, the screen for notifying the success of the performance is 

displayed. Then press the [OK] button. If the screen for notifying a failure of the performance is 
displayed, quit this operation by pressing the [NO] button. Then check that the one-time dongle is 
installed properly in the equipment.

(9) Check that the installed license is displayed on the license list.

Remarks: 

If there are any other licenses to be installed, repeat from step (4). If there are no other licenses 
to be installed, press the [CLOSE] button, and then turn the power OFF.

[H] Check firmware versions

• System firmware version (08-9930)

Notes: 

If the security mode is changed from High Security to Low Security in the step "[A] Return 
License", set the value of 08-8911 to "3" (High Security).

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов