Toshiba e-Studio477s Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 482

Toshiba e-Studio477s Скачать руководство пользователя страница 102

e-STUDIO477S/527S/477SL

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

SETTING / ADJUSTMENT

4 - 22

4.4.15

Color conversion table selection

The color conversion table for each original mode at color scanning can be selected as follows.

<Adjustment Mode (05)>

Notes:

When "For reproduction of pure color" is selected, the colors other than pure colors of CMY
might change.

<Procedure>

(1) While pressing [0] and [5] simultaneously, turn the power ON.
(2) Key in the codes to be adjusted and press the [START] button.
(3) Key in the adjustment value.

(To correct a value once keyed in, press the [CLEAR] button.)

(4) Press the [OK] or [INTERRUPT] button to store the value in memory.



The equipment goes

back to the ready state.

(5) Let the equipment restart and perform the scanning job.
(6) If the desired image has not been attained, repeat step (2) to (5).

Code

Original mode Item to be adjusted

Remarks

8305

Text/Photo

Color conversion

table

0: Color conversion for text or photo

1: Color conversion for text/photo

2: For reproduction of pure color

* "For reproduction of pure color" increases

the color reproduction of the pure color patch

for CMY.

8308

Custom mode

«
...
100
101
102
103
104
...
»

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов