Toshiba e-Studio477s Скачать руководство пользователя страница 320

Страница: 320 / 482

e-STUDIO477S/527S/477SL

BACKUP FUNCTION

9 - 2

9.1.3

Backup files

The following files are saved in the root directory of the USB device by backing up.

9.1.4

Cloning procedure

[A] Backup procedure

(1) Press the [ON/OFF] button to shut down the equipment.

(2) Connect the USB device [1] to the USB port [2] on the right upper cover.

Fig. 9-3

Notes:

Backing up cannot be performed with multiple USB device [1] connected at the same time.

(3) Turn the power ON while pressing [6] and the [CLEAR] button simultaneously.

(4) When "SRAM Clear Mode" appears on the LCD, key in [0] to select "0. Set Serial Number" and

then press the [START] button.

(5) Key in the serial number on the label attached to the rear cover of the equipment, and then press

the [OK] button.

(6) "Serial Number Setting completed" is displayed.

(7) Turn the power OFF.

(8) Turn the power ON while pressing the [5] and [9] buttons simultaneously.

(9) Enter the password, and then press the [OK] button.

(If the password is not set for Service, press the [ENTER] button without entering anything.)

(10) Select "1. Backup SRAM Data to USB", and then press the [START] button.

(11) Enter a password (max. 15 characters) set for the backup data.

(12) "Backup Successfully done Restore the MFP" is displayed on the LCD screen when the backup

has been properly completed.

Filename

Remark

Modelname_MFPSerialNo_yyyy-MM-dd_hh-mm

E.g.: When backup was performed at 13:59 on
October 1st, 2010.
T290_CUK911379_2010-10-01_13-59

[2]

[1]

Содержание e-Studio477s


























































































































































































































































































































































































































































































Результаты поиска

Содержание e-Studio477s

Отзывы:

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 320 / 482

Результаты поиска

Содержание e-Studio477s

Отзывы: