manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 297 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 297

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO477S/527S/477SL

FIRMWARE UPDATING

8 - 9

8

The screen for selecting items to be updated is displayed after approx. 3 minutes. 
On this screen, the current firmware version of this equipment and the firmware version of data to 
be updated are displayed.

Fig.8-9

Firmware Update Mode

System Firmware Version  : xxxx(x.x.x.x)

Update Mode 

 

: USB Update

Select Firmwares

1. SYSTEM FIRMWARE (OS Data)

2. ENGINE FIRMWARE

    * PU LOADER FIRMWARE

    * PU FIRMWARE

    * OPTION TRAY FIRMWARE

    * LCF FIRMWARE

    * FINISHER FIRMWARE

    * DUPLEX FIRMWARE

3. SCANNER FIRMWARE

    * SU LOADER FIRMWARE

    * SU RECOVERY FIRMWARE

    * SU FIRMWARE

4. SYSTEM SOFTWARE (HD Data)

    * FILE SYSTEM SOFTWARE

    * APPLICATION SOFTWARE

Updater Version

xxxxxxxxxxxx

xxxxxxxxxxxx

xxxxxxxxxxxx

Installed Version

xxxxxxxxxxxx

xxxxxxxxxxxx

xxxxxxxxxxxx

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов