manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 184 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 184

e-STUDIO477S/527S/477SL

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

ERROR CODE AND TROUBLESHOOTING

5 - 80

[2E40] Image conversion abnormality in USB storage

Turn the power OFF and then back ON.  Perform the job in error again. Replace the main memory 
and then perform the job in error again.

[2E43] Encryption failure in USB storage

Turn the power OFF and then back ON. Perform the job in error again.

[2E44] Encryption PDF enforced mode error in USB storage

Reset the encryption and perform the job in error again. To create an image file not encrypted, 
consult your administrator.

[2E45] Meta data creation error in USB storage (Scan to File)

Check the template settings. Perform the job in error again. If the error still occurs, turn the power 
OFF and then back ON, and then perform the job in error again.

[2E65] File creation error due to insufficient USB folder capacity

Delete unnecessary files in the folder.

[2E66] HDD full failure in USB storage

Delete the job in progress or being set or in the HOLD/PRIVATE/PROOF/INVALID, and perform it 
again.
Check if the server or local disk has a sufficient space in disk capacity.
Check that there is enough space in the USB memory.

[2EC1] Power failure in USB storage

Check if the power cable is connected properly and inserted securely. Check if the power voltage is 
unstable.

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов