manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 168 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 168

e-STUDIO477S/527S/477SL

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

ERROR CODE AND TROUBLESHOOTING

5 - 64

* AccessFailed or KeyMismatch

[F109_6] Key consistency error (administrator password error for ADI-HDD authentication)

Take measures given in the following table according to the messages displayed in the SRAM Key 
Status and FROM Key Status fields. 

Remarks: 

If the error is not cleared, reinstallation of the system firmware, system software and application 
is needed. ([4]+[9] 



Power-ON)

KeyNull/
KeyBroken

KeyNull/
KeyBroken

<No USB backup data>
1. Create the partition in the HDD, and reinstall the system 

software.

 P. 6-13 "6.2.3 Precautions and procedures when 

replacing the HDD"(Perform step 3 or later in “[E]Replace / 
Format HDD”)

<With USB backup data: All key data recovery>
1. Recover all the data on the SRAM board.

[5] + [9] + [POWER] 

 2. Restore SRAM Data from USB

(For details, see "9.1.4Cloning procedure [B]Restore 
procedure")

2. Recover the encryption key/license on the SYS board.

Follow the procedures below noted in "6.2.4Precautions 
and Procedures when replacing the SYS board".
[C] Restore ADI key (only when ADI-HDD is installed)
[D] Restore encryption key
[E] Restore license

KeyMismatch

KeyMismatch

<The error occurs when the SYS board is replaced>
Recover the encryption key on the SYS board. (Transfer the 
license from SYS-SRAM to SYS-FROM.)

 P. 6-18 "6.2.4 Precautions and Procedures when replacing 

the SYS board"([C]Restore ADI key)
<The error occurs except when the SYS board is replaced>
Recover the encryption key on the SRAM board. (Transfer the 
license from SYS-FROM to SYS-SRAM.)

 P. 6-22 "6.2.5 Precautions and procedure when replacing 

the SRAM board (for the SYS board)"([G]Backup ADI key)

Classification

Contents

Other service call

Key consistency error - Administrator password error for ADI-
HDD authentication.

Check item

Measures

Encryption key status confirmation

Check the message displayed by [3] + [C] + [POWER] 

 5. Key 

Backup Restore.

SRAM Key 

Status

FROM Key 

Status

Measure

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов