manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 452 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 452

 

Maintenance Utility Operating Manual 42678819FU02 - 16/38 

 

2.4.1.1.1. 

PU board replacement   

This is a function for PU board replacement.

 

The function uploads the settings from the PU board to be replaced and saves the data to allow settings to be 

downloaded to the newly installed PU board. 

At the time of replacement with an alternate device, you can copy board setting values to the alternative 

device using this function. 

 

(1)

 

Displaying the function screen 

Click "PU board replacement" to display the function screen for PU board replacement. 

 

 

(a)

 

ID string input area 

(b)

 PU board setting value upload/save button 

(c)

 PU board setting value download button 

(d)

 PU board setting value delete button 

 

(a) 

(b) 
(c) 

(d) 

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов