manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 223 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 223

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO477S/527S/477SL

REPLACEMENT OF PC BOARDS/HDD

6 - 9

6

6.2

Precautions, Procedures and Settings for Replacing PC 
Boards and HDD

6.2.1

Precautions when replacing PC boards

• The ID for each equipment is registered on the PU board, the SYS board and SU board. So, if their 

replacement is required, be sure to replace only one board at a time.  Do not replace the SYS board 
and the SRAM board (for the SYS board) together.

• If both the PU board and SYS board require replacement, replace them in the following procedure.

1. First, replace one of the board to be replaced.
2. Turn the power ON and confirm that “READY” is displayed.
3. Turn the power OFF.
4. Replace another board that requires replacement.

• When the HDD requires replacement, see “6.2.3Precautions and procedures when replacing the 

HDD”.

• When the SYS board requires replacement, see “6.2.4Precautions and Procedures when replacing 

the SYS board”.

• When SRAM board requires replacement, see “6.2.5Precautions and procedure when replacing the 

SRAM board (for the SYS board)”.

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов