manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 82 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 82

e-STUDIO477S/527S/477SL

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

SETTING / ADJUSTMENT

4 - 2

4.1.2

Image Dimensional Adjustment

There are several adjustment items in the image dimensional adjustment, as listed below.

*1: Adjustment can be done only for enlarging image.

[Procedure to key in adjustment values]

In accordance with the procedure described below, make adjustment of each adjustment item so that 
the measured values obtained from test copies satisfy the specification. By pressing the [FAX] button, 
immediately after starting the Adjustment Mode (05), single-sided test copying can be performed 
(normal copy mode).

Fig.6-1

Item to be adjusted

Code in mode 05

Image 
dimensional 
adjustment 
in the copy/
printer/fax 
function

Reproduction ratio adjustment of primary scanning 
direction (PPC)

7000

Reproduction ratio adjustment of primary scanning 
direction (PRT/FAX)

7001*1

100%

A

A4

TEST MODE

100%

A

A4

TEST MODE

100%

A

A4

Wait Warming Up

100%

A

A4

COPYING

100%

XXX

A4

TEST MODE

YYY

ZZZ

Current adjustment value

Adjustment value newly keyed in.

(If no entering, YYY is displayed.)

Code No.

1

0

5

POWER

OK

INTERRUPT

Digital keys

START

: Key in codes.

<Operation keys>

<Display>

Power OFF/ON : Exit the Adjustment Mode.

Test copy

Digital keys

FAX

START

: Key in adjustment

  values.

Value ZZZ is stored

replacing values YYY.

If the test copy does not

satisfy the specified values,

return to step  1  and

repeat the adjustment

procedure.

or

( CLEAR  Use to make corrections)

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов