Toshiba e-Studio477s Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 482

Toshiba e-Studio477s Скачать руководство пользователя страница 7

ALLEGEMEINE SICHERHEITSMASSNAHMEN IN BEZUG
AUF DIE WARTUNG

Die Installation und die Wartung sind von einem qualifizierten Service-
Techniker durchzuführen.

1. Transport/Installation

- Das Tragen oder Installieren des Gerätes braucht wenigstens zwei Menschen. Die angezeigten

Stellen sind wie in der Abbildung festzuhalten. Das Gerät ist ziemlich schwer und wiegt ungefähr
55 kg (mit dem Finisher); deshalb wenn Sie es hochheben oder tragen, passen Sie besonders
auf.

- Beim Transportieren des Geräts nicht an den beweglichen Teilen oder Einheiten (z.B. das

Bedienungsfeld, die Duplexeinheit oder die automatische Dokumentenzuführung) halten.

- Eine spezielle Steckdose mit Stromversorgung von AC 110V/15A, 120V/12A, 220-240V/8A als

Stromquelle verwenden.

- Das Gerät ist aus Sicherheitsgründen zu erden.
- Einen geeigneten Standort für die Installation wählen. Standorte mit zuviel Hitze, hoher

Luftfeuchtigkeit, Staub, Vibrieren und direkter Sonneneinstrahlung sind zu vermeiden.

- Um einen optimalen Kopierbetrieb zu gewährleisten, muss ein Abstand von mindestens 30 cm

links, 30 cm rechts und 60 cm dahinter eingehalten werden.

- Das Gerät ist in der Nähe der Steckdose zu installieren; diese muss leicht zu erreichen sein.
- Nach der Installation muss das Netzkabel richtig hineingesteckt und befestigt werden, damit

niemand darüber stolpern kann.

- Falls der Auspackungsstandort und der Installationsstandort des Geräts verschieden sind, die

Bildqualitätsjustierung (automatische Gammajustierung) je nach der Temperatur und
Luftfeuchtigkeit des Installationsstandorts und der Papiersorte, die verwendet wird, durchführen.
- Wenn das Gerät Rollen hat, sind sie nach der Installation zu verriegeln.

«
...
5
6
7
8
9
...
»

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов