Toshiba e-Studio477s Скачать руководство пользователя страница 190

Страница: 190 / 482

e-STUDIO477S/527S/477SL

ERROR CODE AND TROUBLESHOOTING

5 - 86

[5015] Invalid SSL certificate

[5016] Expired SSL certificate

[5017] Other SSL certificate related error

[5018] Invalid DNS error

[5019] Connection error

Classification

Error item

Communication error with external
application

SSL certificate is not valid.

Check item

Measures

Setting

Install the correct SSL certificate.

Classification

Error item

Communication error with external
application

SSL certificate is expired.

Check item

Measures

Setting

Set the correct time.

Classification

Error item

Communication error with external
application

SSL certificate is invalid.

Check item

Measures

Setting

Install the correct SSL certificate.

Classification

Error item

Communication error with external
application

DNS address is invalid.

Check item

Measures

Setting

Set the correct DNS address.
If any setting is needed in DNS, consult your administrators.

Classification

Error item

Communication error with external
application

Settings for initial URL and proxy are incorrect.

Check item

Measures

Setting

Perform the correct settings for initial URL and proxy.

Содержание e-Studio477s


























































































































































































































































































































































































































































































Результаты поиска

Содержание e-Studio477s

Отзывы:

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 190 / 482

Результаты поиска

Содержание e-Studio477s

Отзывы: