manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 84 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 84

e-STUDIO477S/527S/477SL

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

SETTING / ADJUSTMENT

4 - 4

4.2

Image Quality Adjustment (Copying Function)

4.2.1

Automatic gamma adjustment

When the reproduction of gradation is not appropriate, the gradation reproducibility can be corrected by 
performing this automatic gamma adjustment. In case the gradation reproduction of the image checked 
is not satisfactory, make this adjustment as described below at parts replacement.

When unpacking or any of the following parts has been replaced, be sure to make this adjustment:
• Drum unit
• Transfer belt unit
• SRAM board (SYS board)
• PU board
• HDD

Notes: 

Be sure that this adjustment be made after performing the image adjustment in 

 P. 4-2 "4.1.2 

Image Dimensional Adjustment".

<Procedure>

(1) While pressing [0] and [5] simultaneously, turn the power ON. 

 Adjustment Mode

(2) Select the A4/LT drawer. Key in the pattern number and press the [FAX] button to output a “Patch 

chart for gamma adjustment”.

<Adjustment Mode (05)>

(3) Place the patch chart for adjustment printed in step (2) face down on the original glass.

Place the chart aligning its side with a black square against the original scale.

(4) Key in a code and press the [START] button.

 The scanner reads the chart automatically and performs automatic gamma adjustment 

calculation (approx.30 sec.).

<Adjustment Mode (05)>

(5) When the adjustment has finished normally, press the [OK] button to have the adjustment results 

reflected.
(To cancel the reflection of adjustment results, press the [CANCEL] button.)
In the case of an abnormal ending, “ADJUSTMENT ERROR” is shown.
Press the [CANCEL] button to clear the error display. When it is cleared, the control panel display 
will return to the ready state. Then, check if the patch chart on the original glass is placed in the 
wrong direction or if it is placed inclined on the original glass, and then repeat step (3) and 
afterward.

Pattern No.

Pattern No.

Remark

Paper type

10

Black

When performing code 05-7165

All paper types

Code

Item to be adjusted

Contents

7165

Automatic gamma
adjustment

When the reproduction of gradation is not appropriate, the gradation 
reproducibility can be corrected by performing this automatic gamma 
adjustment. The result of 7165 is applied to all paper types.

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов