manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 227 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 227

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO477S/527S/477SL

REPLACEMENT OF PC BOARDS/HDD

6 - 13

6

6.2.3

Precautions and procedures when replacing the HDD

Notes: 

• When the HDD is replaced, it is necessary to back up the data in the HDD before replacing and 

to recover them after replacing.

• To maintain the security, ask users to perform the backup/restore for users’ data/information in 

the HDD. The service technician can perform them only when users permit it.

• Some data in the HDD cannot be backed up and can be kept only on the paper.
• Do not replace the HDD and the SRAM board (for the SYS board) together.
• When the HDD is replaced, do not perform SRAM data formatting (Clear SRAM) before the 

normal start-up.

• When the HDD is replaced, do not restore the back-up file before the normal start-up.

A procedure for replacing the HDD is shown below.

Fig.6-23

Start

[A] Back up data in HDD

[B] Print out "FUNCTION LIST FOR MAINTENANCE"

[C] Print out "FUNCTION" list

[D] Erase HDD

[E] Replace/Format HDD

[F] Reset user's setting item and restore data/information

[G] Reset "FUNCTION LIST FOR MAINTENANCE"

[H] Reset "FUNCTION" list

Setting completed

[I] Adjust image quality

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов