Toshiba e-Studio477s Скачать руководство пользователя страница 472

Страница: 472 / 482

Maintenance Utility Operating Manual 42678819FU02 - 36/38

B Limitations of Maintenance Utility

Limitations of the host (PC) side

(1)

User restriction

privileges.

(2)

Limitations of Windows 2000

When using Windows 2000, confirm that it is installed with Service Pack 1 or later.

When the printer is connected via USB using a version older than Windows 2000 Service Pack 1, the

communication function may not operate properly.

Limitations of the Maintenance Utility function

(1)

Limitations for activating Maintenance Utility

Before activating Maintenance Utility, be sure that the printer to be maintained using the utility is on-line;

improper communication with the printer can result. For using the utility with the printer not equipped with

image drum(s), or the cover of the printer opened, and placed off-line, send the printer into forced on-line

mode before activating the utility. See Appendixes F for the procedure for establishing forced on-line mode.

(2)

Limitations of the PU board setting value download function

After the PU board setting value is uploaded, if the download operation is conducted without restarting the

printer, a communication error may occur.

Содержание e-Studio477s


























































































































































































































































































































































































































































































Результаты поиска

Содержание e-Studio477s

Отзывы:

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 472 / 482

Результаты поиска

Содержание e-Studio477s

Отзывы: