manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 295 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 295

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO477S/527S/477SL

FIRMWARE UPDATING

8 - 7

8

8.2.4

Update procedure

Important: 

• The file system of a USB device should be formatted in the FAT or FAT32 format. USB devices 

formatted in an NTFS or another format will not be able to be operated. The file system of a USB 
device can be confirmed by opening its property using Windows Explorer or such.

• Never shut down the equipment during an update. Otherwise, firmware data and the following 

option data (if installed) could be damaged and may not be able to be operated properly.

- Data Overwrite Enabler (GP-1070)
- Meta Scan Enabler (GS-1010)
- External Interface Enabler (GS-1020)
- IPSec Enabler (GP-1080)
- Unicode Font Enabler (GS-1007)

[A] Updating firmware

(1) Connect the USB device to the PC and write the model specific folder in which the data file is 

stored.
Store the data file for updating in the model specific folder.

(2) Press the [ON/OFF] button to shut down the equipment.

(3) Connect the USB device [1] to the USB port [2].

Fig.8-7

[2]

[1]

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов