manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 454 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 454

 

Maintenance Utility Operating Manual 42678819FU02 - 18/38 

 

(3)

 

Uploading and saving the PU board setting value 

Click [Upload and save the PU board setting value] in the "PU board replacement - Menu" screen to 

upload and save the PU board setting value. 

 

If a PU board setting value of the same ID string has been saved, the following check window is 

displayed. 

 

 

If the PU board setting value has not been stored or the [OK] button in the above confirmation window 

is clicked, go to the window that "PU board replacement - Upload and Save", and uploading of the PU 

board setting value starts.   

(The upload operation may take several minutes. Do not perform any operations until the upload 

operation is complete.) 

 

Uploading. Wait 

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов