manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 312 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 312

e-STUDIO477S/527S/477SL

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

FIRMWARE UPDATING

8 - 24

8.4.1

FAX unit firmware (GD-1340)

Important: 

• Before updating the FAX firmware, make sure to print out the current Function list for 

maintenance, Function list (ADMIN), Address book list and Group number information. In 
case the updating is failed and the registered information of the users is lost for some reason, 
re-register the user information referring to the lists and recover it.

• Confirm the following items before turning OFF the power of the equipment. Turning OFF the 

power may clear the data below.
-    Confirm that the “MEMORY RX” LED is OFF and there are no memory reception data.
-    Press the [JOB STATUS] button to display the screen and then confirm that there are no
     memory transmission data.
-    Print the “Mailbox/Relay box report” and then confirm that there are no F code data.

[A] Update Procedure

(1) Install the ROM to the download jig (K-PWA-DLM-320).

Make sure the direction is correct.

(2) Press the [ON/OFF] button to shut down the equipment.

(3) Take off the right side cover.

 P. 6-1 "6.1.1 Right side cover"

(4) Connect the download jig [1] with the jig connector [2] on the FAX board.

Fig.8-16

[2]

[1]

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов