Toshiba e-Studio477s Скачать руководство пользователя страница 206

Страница: 206 / 482

e-STUDIO477S/527S/477SL

ERROR CODE AND TROUBLESHOOTING

5 - 102

[8039] IKEv1 invalid signature

[803A] IKEv2 wrong proposal choosen

[803B] IKEv2 Certificate failed

[803C] IKEv2 secret key authentication failed

[803D] IKEv2 falling back to IKEv1

Classification

Error item

Network error

Ipsec error for invalid signaturer for certificate

Check item

Measures

Setting

Mismatch in Signature payload (MAC or IV).
Check the CA and user certificate in MFP and peer machine.

Classification

Error item

Network error

Ipsec error is proposal choosen is wrong

Check item

Measures

Setting

Check the IKEv2/IPsec proposal parameters (encryption/
authentication algorithms, DH group, authentication methods)
in MFP and peer machine.

Classification

Error item

Network error

Ipsec error for ikev2 certification failed

Check item

Measures

Setting

Check
1. CA and user certificate in both MFP and remote peer -

certificate timestamp and IPsec Certificate template
should be valid.

2. CRL DP server name is mapped in MFP’s host table or

DNS entry.

3. Certificate against CRL.

Classification

Error item

Network error

Ipsec error for ikev2 if secret key auth failed

Check item

Measures

Setting

Mismatch in IKEv2 Pre Shared Key. Check the PSK in MFP
and peer machine.

Classification

Error item

Network error

Ipsec error if peer dosent support IKEv2 and falling back to
IKEv1

Check item

Measures

Setting

Remote machine is not supporting IKEv2. Going back to use
IKEv1.

Содержание e-Studio477s


























































































































































































































































































































































































































































































Результаты поиска

Содержание e-Studio477s

Отзывы:

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 206 / 482

Результаты поиска

Содержание e-Studio477s

Отзывы: