Toshiba e-Studio477s Скачать руководство пользователя страница 430

Страница: 430 / 482

e-STUDIO477S/527S

05/08

Mode

Element

Sub Element

Item

Subitem

Code

Sub-

Code

Details

Default

value

Acceptable

value

RAM

Contents

Proc

edure

ServiceUI

Suspend when quota is

empty

Sets whether the process is suspended

immediately or suspended after the job is

completed if quota is used up.

0: Suspended immediately

1: Suspended after the job is finished

Setting

mode

System

Counter

9787

0~1

SYS

Service call checking period

setting

0: No checking period specified (= Calls service

technician immediately)

1: 10 minutes

2: 30 minutes

3: 1 hour

4: 6 hours

5: 12 hours

6: 24 hours

7: 48 hours

8: 7 days

9: 1 month

10: 1 year

11: 5 years

12: Not limited (= Calls service technician if such

error has occurred in the past even once or more)

Setting

mode

System

Maintenance

9788

0~12

SYS

Service Notification setting

Enables to set up to 3 E-mail addresses to be sent.

(08-9794, 9607, 9608)

0: Invalid

1: Valid (E-mail)

2: Valid (FAX)

Setting

mode

System

Maintenance

Remote-

controlled service

9793

0~2

SYS

Destination E-mail address 1

Maximum 192 letters

Setting

mode

System

Maintenance

Remote-

controlled service

9794

SYS

Total counter information

transmission setting

0: Invalid

1: Valid

Setting

mode

System

Maintenance

Remote-

controlled service

9795

0~1

SYS

Total counter transmission

date setting

0 to 31

Setting

mode

System

Maintenance

Remote-

controlled service

9796

0~31

SYS

Temporary communication

password setting

Sets a temporary communication password. The

password can be entered in alphanumeric

characters (A to Z, a to z, 0 to 9) up to 10 digits.

The entered password is displayed with "*" on the

touch panel and the self-diagnostic lists.

(Maximum 10 digits, minimum 5 digits)

Setting

mode

System

Network

9798

99999

SYS

Switchover of mode

Sets the authentication mode when "0: (Internal

authentication)" is selected in the code 08-9293.

0: Card ID differs from the User ID

1: Card ID is the same as the User ID

Setting

mode

System

User control

Local

authentication

9799

0~1

SYS

Forcible mode change in

toner empty status

0: SLEEP MODE

1: AUTO POWER SAVE

2: READY

Setting

mode

System

Process

9804

0~2

SYS

Firmware version of printer

loader section

Setting

mode

System

Version

Printer

9806

Tray2

Setting

mode

System

Version

Printer

ROM version of

printer optional

tray

9807

00.00.00~F

F.FF.FF

Tray3

Setting

mode

System

Version

Printer

ROM version of

printer optional

tray

9807

00.00.00~F

F.FF.FF

Ver03

08 Setting Mode

Содержание e-Studio477s


























































































































































































































































































































































































































































































Результаты поиска

Содержание e-Studio477s

Отзывы:

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 430 / 482

Результаты поиска

Содержание e-Studio477s

Отзывы: