manualshive.com logo in svg

Toshiba e-Studio477s, Руководство по обслуживанию, Страница: 125 / 482

Поделиться
Скачать
Toshiba e-Studio477s Скачать руководство пользователя страница 125

© 2013-2016 TOSHIBA TEC CORPORATION All rights reserved

e-STUDIO477S/527S/477SL

ERROR CODE AND TROUBLESHOOTING

5 - 21

5

6033

No entering record.

Card related error: Invalid flag 
data (no room-entry data): The 
card cannot be used because no 
room-entry data are recorded in 
it.

P. 5-92

6034

Illegal entering record.

Card related error: Invalid flag 
data (invalid card data): The card 
cannot be used because the data 
required for the use of the card 
are not correctly set.

P. 5-92

6041

Card Authentication Failed 
because of Card Reading Error

Card authentication: Card related 
error: Card data cannot be 
obtained correctly.

P. 5-92

6042

Card Authentication Failed 
because of setting Error

Card authentication: Card setting 
error: The self-diagnostic code 
required for card authentication is 
not set in this equipment 
correctly.

P. 5-92

6121

SecureErase fails

Automatic Secure Erase failure

P. 5-92

6131

SNTP server synchronization 
failure

Synchronization with the SNTP 
server failed.

P. 5-93

Error code

Message displayed in the 

TopAccess screen

Contents

Troubleshooting

Содержание e-Studio477s



































































































































































































































































































































































































































































































Отзывы:

Нет отзывов